ACS724 Current Sensor Carrier - module with ACS724 0-10A current sensor
ID: 586598
5906623480463
zł45.61
Tax included
zł37.08 tax excl.
Module with ACS724LLCTR-10AU current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4042
Description
Module with a one-way Hall current sensor based on the ACS724LLCTR-10AU chip. It allows you to measure the current in the range from 0 to 10 A. The board is powered with the voltage from 4.5 V to 5.5 V and is intended for use in circuits with a logical voltage of 5 V. It offers a current path with low resistance (~ 1.2 mΩ) and electrical insulation up to 2.4 kV RMS. The output is a proportional analog voltage (400 mV/A) centered at 0.5 V with an error of ± 1.5%.
The sensor requires five connections to work properly: input current (IP+ and IP-), logic power (VCC and GND) and sensor output (OUT). Pin FILTER allows you to adjust the bandwidth of the plate by adding a capacitor to ground in parallel with the 1 nF capacitor that is already on the board. Without an additional external filter capacitor, the frequency response is approximately 90 kHz.
Features
- Hall effect differential detection
- Internal resistance of 1.2 mΩ conducting path
- Electrical insulation up to 2.4 kV RMS
- 120kHz high bandwidth for fast response times
- Ability to filter the output data to improve the resolution
- Integrated digital temperature compensation circuit
- Operating voltage 4.5 to 5.5 V
- Current measuring range from 0 to 10 A
- Output resolution 0.4 V/A
- Working temperature range from -40°C to 150°C
- Dimensions: 17.8 x 20.3 mm
- Weight: 1.1 g
Kit contains
- ACS724 Current Sensor Carrier module
- Straight 3-pin male connector
586598
Data sheet
- Interface
- Sygnał analogowy
- Zakres pomiarowy
- 0 - 10 A
- Sposób podłączenia
- Szeregowy
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Module with ACS724LLCTR-30AU current sensor with a measuring range of direct and alternating current from 0 to 30 A. It communicates via an analog interface. Pololu 4046
zł40.55
24h
Available quantity: 1
Available
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 5A. DFRobot SEN0287
zł81.82
24h
Available quantity: 3
Available
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.31
24h
Available quantity: 430
Available
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.31
24h
Available quantity: 163
Available
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
zł5.10
24h
Available quantity: 837
Available
Module with ACS724LLCTR-05AB current sensor with a measuring range of direct and alternating current from -5 to 5 A. It communicates via an analog interface. Pololu 4041
zł34.77
24h
Available quantity: 3
Available
Other products in the same category (16)
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5255
zł55.92
24h
Available quantity: 2
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5256
zł56.70
24h
Available quantity: 2
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5257
zł55.93
24h
Available quantity: 1
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5258
zł58.79
24h
Available quantity: 2
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5259
zł52.52
24h
Available quantity: 5
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5260
zł58.79
24h
Available quantity: 2
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5262
zł53.82
24h
Available quantity: 2
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5263
zł50.06
24h
Available quantity: 3
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5270
zł66.95
24h
Available quantity: 3
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5271
zł71.45
24h
Available quantity: 5
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5272
zł71.45
24h
Available quantity: 2
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5273
zł71.45
24h
Available quantity: 5
Available
Large Carrier version current sensor from Pololu, model 5274, based on the ACS72981LLRATR-100B5 IC, designed for measuring current in the range from -100 A to +100 A at a 5 V supply in applications requiring galvanic isolation and analog output. Pololu 5274
zł62.84
24h
Available quantity: 3
Available
Large Carrier version current sensor from Pololu, model 5275, based on the ACS72981LLRATR-100U3 IC, designed for measuring current in the range from 0 A to 100 A at a 3.3 V supply in applications requiring galvanic isolation and analog output. Pololu 5275
zł62.84
24h
Available quantity: 3
Available
Large Carrier version current sensor from Pololu, model 5276, based on the ACS72981LLRATR-100U5 IC, designed for measuring current in the range from 0 A to 100 A at a 5 V supply in applications requiring galvanic isolation and analog output. Pololu 5276
zł62.84
24h
Available quantity: 3
Available
Large Carrier version current sensor from Pololu, model 5277, based on the ACS72981KLRATR-150B3 IC, designed for measuring current in the range from -150 A to +150 A at a 3.3 V supply in applications requiring galvanic isolation and analog output. Pololu 5277
zł62.84
24h
Available quantity: 3
Available
Module with ACS724LLCTR-10AU current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4042