Gravity: Analog AC Current Sensor - module with an analog AC 5A current sensor
ID: 581618
5906623406456
zł81.82
Tax included
zł66.52 tax excl.
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 5A. DFRobot SEN0287
Description
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 5 A. The probe is connected to the measuring module via a 3.5 mm Jack connector. The measuring module has an analog output compatible with the Gravity standard. The set allows you to easily measure AC current with a microcontroller without the need to cut the wires. It allows the construction of an automatic monitoring system for an AC motor or measurements of lighting and electrical equipment. On the Wiki page there is a user manual with sample Arduino code.
_1.jpg)
Features
AC Current Signal Conversion Module
- Input Voltage (VCC): 3.3V to 5.5V
- Interface: Gravity Analog (PH2.0-3P，analog voltage output 0.2-2.8V DC)
- AC Voltage Input Range: 0-1V (AC RMS)
- Relative Error: ±4%
- Dimension: 32×27 mm
- Weight: 5g
Open Type AC Transformer Probe
- AC Current Range: 0 to 5A
- Signal Output (standard Φ3.5mm 3P plug): 0-1V AC voltage, linear corresponding range 0-5A
- Accuracy: ±1%
- Non-linearity: ≤±0.2%
- Frequency Range: 50Hz to 1kHz
- Cable Length: 1m
- Working Temperature: -25 ℃ to 70 ℃
- Opening Size: 13×13 mm
- Weight: 50g
Kit contains
- AC Current Signal Conversion Module
- Open Type AC Transformer Probe (5A)
- Gravity-3P Analog Sensor Cable
581618
Data sheet
- Interface
- Sygnał analogowy
- Zakres pomiarowy
- 0 - 5 A
- Sposób podłączenia
- Nieinwazyjny
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.57
24h
Available quantity: 113
Available
Available
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
zł21.92
24h
Available quantity: 6
Available
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 20 A. DFRobot SEN0211
zł91.49
24h
Available quantity: 1
Available
Module with an analog current sensor. Enables measurement of alternating and direct current up to 20 A. DFRobot SEN0214
zł40.22
24h
Available quantity: 1
Available
Board with ATmega1280 microcontroller from the AVR family, the user has 54 I/O lines, 14 PWM channels, 16 analog inputs. DFRobot DFR0003
zł89.20
Delivery date unknown
No product available!
Module with an analog current sensor. It enables the measurement of AC and DC current up to 50 A. DFRobot SEN0098
zł134.91
Delivery date unknown
No product available!
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 10 A. DFRobot SEN0288
zł108.03
24h
Available quantity: 10
Available
Other products in the same category (16)
ACS714 Current Sensor Carrier -5 to +5A
zł107.82
24h
Available quantity: 1
Available
ACS714 Current Sensor Carrier -30 to +30A
zł49.70
24h
Available quantity: 2
Available
ACS711EX Current Sensor Carrier -31A to +31A
zł19.98
24h
Available quantity: 4
Available
ACS711EX Current Sensor Carrier -15.5A to +15.5A
zł20.06
24h
Available quantity: 5
Available
The current measurement of 0 - 30A is carried out by the ACS712-30 system based on the Hall effect. The sensitivity of the system is 66mV / A (analog signal).
zł6.86
4 weeks
No product available!
No product available!
No product available!
No product available!
No product available!
Available
The current measurement with the value 0-20A is carried out by the ACS712-05 system based on the Hall effect. The sensitivity of the system is 100mV / A (analogue signal) .modACS712-20
zł14.97
24h
Available quantity: 20
Available
The current measurement with a value of 0 - 5A is realized by the ACS712-05 system based on the Hall effect. The system sensitivity is 185mV / A (analog signal).
zł8.95
4 weeks
No product available!
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 20 A. DFRobot SEN0211
zł91.49
24h
Available quantity: 1
Available
The module with a TA12-200 current sensor with a measuring range of alternating current up to 5 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020027
zł41.34
24h
Available quantity: 1
Available
Module with an analog current sensor. Enables measurement of alternating and direct current up to 20 A. DFRobot SEN0214
zł40.22
24h
Available quantity: 1
Available
Module with INA219 system with bi-directional current meter
zł10.01
4 weeks
No product available!
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 5A. DFRobot SEN0287