ACS724 Current Sensor Carrier - module with ACS724 ±20A current sensor
ID: 586600
5906623480487
zł44.72
Tax included
zł36.36 tax excl.
Module with ACS724 current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4045
Description
Module with a two-way Hall current sensor based on the ACS724LLCTR-20AB system. It allows you to measure the current in the range from -20 to 20 A. The board is powered with the voltage from 4.5 V to 5.5 V and is intended for use in circuits with a logical voltage of 5 V. It offers a current path with low resistance (~ 1.2 mΩ) and electrical insulation up to 2.4 kV RMS. The output is a proportional analog voltage (100 mV/A) centered at 2.5 V with an error of ± 0.8%.
The sensor requires five connections to work properly: input current (IP+ and IP-), logic power (VCC and GND) and sensor output (OUT). Pin FILTER allows you to adjust the bandwidth of the plate by adding a capacitor to ground in parallel with the 1 nF capacitor that is already on the board. Without an additional external filter capacitor, the frequency response is approximately 90 kHz.
Features
- Hall effect differential detection
- Internal resistance of 1.2 mΩ conducting path
- Electrical insulation up to 2.4 kV RMS
- 120kHz high bandwidth for fast response times
- Ability to filter the output data to improve the resolution
- Integrated digital temperature compensation circuit
- Operating voltage 4.5 to 5.5 V
- Current measuring range from -20 to 20 A
- Output resolution 0.1 V/A
- Working temperature range from -40°C to 150°C
- Dimensions: 17.8 x 20.3 mm
- Weight: 1.1 g
Kit contains
- ACS724 Current Sensor Carrier module
- Straight 3-pin male connector
586600
Data sheet
- Interface
- Sygnał analogowy
- Zakres pomiarowy
- ±20 A
- Sposób podłączenia
- Szeregowy
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 20 A. DFRobot SEN0211
zł92.27
24h
Available quantity: 1
Available
Module with ACS724LLCTR-30AU current sensor with a measuring range of direct and alternating current from 0 to 30 A. It communicates via an analog interface. Pololu 4046
zł40.55
24h
Available quantity: 3
Available
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 5A. DFRobot SEN0287
zł81.82
24h
Available quantity: 3
Available
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.35
Delivery date unknown
No product available!
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.31
24h
Available quantity: 322
Available
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
zł5.49
Delivery date unknown
No product available!
Other products in the same category (16)
No product available!
No product available!
No product available!
No product available!
The current measurement with the value 0-20A is carried out by the ACS712-05 system based on the Hall effect. The sensitivity of the system is 100mV / A (analogue signal) .modACS712-20
zł14.97
24h
Available quantity: 24
Available
The current measurement with a value of 0 - 5A is realized by the ACS712-05 system based on the Hall effect. The system sensitivity is 185mV / A (analog signal).
zł8.95
4 weeks
No product available!
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 20 A. DFRobot SEN0211
zł92.27
24h
Available quantity: 1
Available
The module with a TA12-200 current sensor with a measuring range of alternating current up to 5 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020027
zł41.34
24h
Available quantity: 1
Available
Module with an analog current sensor. Enables measurement of alternating and direct current up to 20 A. DFRobot SEN0214
zł40.22
24h
Available quantity: 1
Available
Module with INA219 system with bi-directional current meter
zł10.01
4 weeks
No product available!
Module with a current and voltage sensor dedicated to Feather boards. Can measure voltage up to 26 V and current up to 3.2 A. Based on INA219 sensor, I2C communication. Adafruit 3650
zł44.90
24h
Available quantity: 1
Available
ACS723 current sensor module with a DC and AC measuring range of ± 5 A. It can read very low currents of 10 mA. It communicates via the analog interface. SparkFun SEN-14544
zł117.16
3 weeks
No product available!
Module with ACS723 current sensor with a measuring range of AC and DC ± 5 A. It communicates via an analog interface. SparkFun SEN-13679
zł64.69
24h
Available quantity: 2
Available
Current-to-voltage converter module designed for devices with a current signal output. It allows linear conversion of current signals from 0 to 25 mA into voltage signals from 0 to 3 V. DFRrobot SEN0262
zł22.37
24h
Available quantity: 5
Available
Module with bi-directional current sensor based on the INA226 system. It allows you to measure current and power, works with a voltage of 0-36 V. It has an I2C interface.
zł12.20
4 weeks
No product available!
A digital precision current sensor module that measures voltage, current and power of electronic modules and devices up to 26V and 8A with a relative error of ± 0.2%. DFRobot SEN0291
zł49.56
24h
Available quantity: 7
Available
Module with ACS724 current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4045