

Pololu Simple High-Power Motor Controller 18v15
The Pololu Simple High-Power Motor Controller makes basic control of brushed DC motors easy, with our free Simple Motor Control Center software enabling quick configuration over USB. The controller supports four interface modes: USB, TTL serial, analog voltage, and hobby radio control (RC). This version operates from 5.5 to 30 V and is efficient enough to deliver a continuous 15 A without a heat sink. It ships with the power capacitor and connectors included but not soldered in, allowing for custom installations.
![]() |
Simple Motor Controllers. |
---|
The Pololu Simple Motor Controllers are versatile, general-purpose motor controllers for brushed, DC motors. A wide operating range of up to 5.5–40V and the ability to deliver up to several hundred Watts in a small form factor make these controllers suitable for many motor control applications. With a variety of supported interfaces—USB for direct connection to a computer, TTL serial for use with embedded systems, RC hobby servo pulses for use as an RC-controlled electronic speed control (ESC), and analog voltages for use with a potentiometer or analog joystick—and a wide array of configurable settings, these motor controllers make it easy to add basic control of brushed DC motors to a variety of projects. Although this motor controller has many more features than competing products, a free configuration utility (for Windows 7, Vista, Windows XP, and Linux) simplifies initial setup of the device and allows for in-system testing and monitoring of the controller via USB.
For 24 V applications, we recommend the 24v12 or 24v23 versions. We strongly recommend against using the 18v7, 18v15, or 18v25 with 24 V batteries, which can significantly exceed 24 V when fully charged and are dangerously close to the maximum voltage limits of these lower-voltage controllers.
![]() |
Simple High-Power Motor Controller 18v25 or 24v23 simplified connection diagram. |
---|
|
|
Note: A USB A to mini-B cable (not included) is required to connect this controller to a computer.
![]() |
Two Pololu Simple Motor Controllers enable mixed RC-control of Dagu Wild Thumper 4WD all-terrain chassis. |
---|
The Simple Motor Controllers are available in several input voltage ranges and output current ranges:
![]() 18v7 | ![]() 18v15 | ![]() 24v12 | ![]() 18v25 | ![]() 24v23 | |
---|---|---|---|---|---|
Absolute max voltage: | 30 V | 30 V | 40 V | 30 V | 40 V |
Recommended max voltage(1): | 24 V | 24 V | 34 V | 24 V | 34 V |
Max continuous current w/o heat sink: | 7 A | 15 A | 12 A | 25 A | 23 A |
Width: | 1.1" (2.8 cm) | 1.1" (2.8 cm) | 1.1" (2.8 cm) | 1.2" (3.1 cm) | 1.2" (3.1 cm) |
Length: | 2.1" (5.3 cm) | 2.1" (5.3 cm) | 2.1" (5.3 cm) | 2.3" (5.8 cm) | 2.3" (5.8 cm) |
Weight(2): | 7 g | 7 g | 7 g | 12 g | 12 g |
Available with connectors installed? | Yes | Yes | Yes | No | No |
1 We do not recommend using the 18v7, 18v15, or 18v25 versions with 24 V batteries, which can significantly exceed 24 V when fully charged. The 24v12 and 24v23 are the much more appropriate controller for 24 V applications.
2 This is the weight of the board without header pins, terminal blocks, or through-hole power capacitor.
|
|
Most Simple Motor Controllers are available “fully assembled”, with the power capacitor and connectors pre-installed, or with these components included but not soldered in. For example, a fully assembled 18v15 ships as shown in the left picture above, and an 18v15 with included hardware ships as shown in the right picture above (the included hardware consists of a power capacitor, a 40×1 straight 0.1" male header strip, a 5mm-pitch 4-pin terminal block, and a blue shorting block).
The connector-free version allows flexibility in choice of connectors and placement of the power capacitor (e.g. on the other side of the board) to accommodate compact installations or to make room for a heat sink.
Note: The power capacitor has a significant effect on performance; the included capacitor is the minimum size recommended, and bigger ones can be added if there is space. A bigger capacitor might be required if the power supply is poor or far (more than about a foot) from the controller.
The included terminal blocks are only rated for 16 A, so we recommend soldering thick wires directly to the connector-free version of the board and using higher-current connectors for applications that will exceed the terminal blocks’ ratings.
|
|
|
Warning: Take proper safety precautions when using high-power electronics. Make sure you know what you are doing when using high voltages or currents! During normal operation, this product can get hot enough to burn you. Take care when handling this product or other components connected to it.
Cechy
Producent BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Osoba odpowiedzialna BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Dual MAX14870 Motor Driver to podwójny sterownik silników DC kompatybilny ze standardem Raspberry Pi pozwalający na wysterowanie dwóch silników DC napięciem 4,5-36V prądem ciągłym 1,7A. Pololu 3758
Wydajny sterownik silnika DC. Pozwala sterować silnikiem o napięciu zasilania w zakresie 6...28 V, silnik może pobierać prąd o natężeniu od 100 A (przy użyciu radiatora). Do sterowania wykorzystywany jest PWM modelarski (np. pochodzące z odbiorników RC) może być używany w robotyce, niewielkich pojazdach elektrycznych lub wszędzie tam gdzie jest potrzeba sterowania silnikiem DC. Digilent 410-334-1
Brak towaru
Moduł dwukanałowego sterownika silników DC oparty o popularny mostek H L298, zasilany napięciem 6-35 V, maksymalny pobór prądu na jeden kanał 2A, radiator do chłodzenia układu. SparkFun ROB-09670
Brak towaru
A4990 Dual Motor Driver Carrier
Podwójny sterownik silników DC przeznaczony dla Arduino, który umożliwia zasilanie silnika napięciem w zakresie 4,5-28V i poborze prądu przy pracy ciągłej 2,6A (5A w szczycie) dwóch silników DC. Pololu 2520
Moduł HAT ze sterownikiem dwóch silników prądu stałego przeznaczony dla Raspberry Pi. Silniki mogą być zasilane napięciem od 6,5 do 30 V i pobierać maksymalnie prąd o natężeniu do 18 A. Pololu 3751
Brak towaru
Sterownik silników DC, który pozwala na kontrolowanie ruchu dwóch napędów za pomocą interfejsu I2C. Płytka bez złączy. Pololu 5047
Brak towaru
Pololu Dual G2 High-Power Motor Driver 24v18 to rozszerzenie pozwalające na sterowanie dwoma silnikami prądu stałego przeznaczone dla Raspberry Pi. Silniki mogą być zasilane napięciem 6,5-36V i pobierać maksymalnie prąd o natężeniu do 18A. Pololu 3756
Brak towaru
Pololu High-Power Motor Driver 36v20 CS
Sterownik silnika prądu stałego (DC) o napięciu pracy 6,5-40V i maksymalnym prądzie ciągłym 21A. Posiada możliwość łatwej realizacji pętli sprzężenia zwrotnego oraz liczne interfejsy sterujące. Pololu 3149
Brak towaru
Dwukanałowy sterownik silników DC z interfejsem UART TTL. Jest zasilany napięciem od 1,8 V do 22 V i może dostarczyć prąd o natężeniu do 1,6 A na silnik. Płytka ze złączami do montażu. Pololu 5081
Mostek H umożliwiający sterowanie jednym silnikiem DC w obu kierunkach lub dwoma jednokierunkowymi przy napięciu od 4,5 do 44 V i prądzie ciągłym do 1,3 A. Moduł oferuje trzy tryby pracy (PH/EN, IN/IN, półmostki), wbudowane ograniczenie i pomiar prądu oraz zabezpieczenia przed przegrzaniem, przeciążeniem, zbyt niskim napięciem i odwrotną polaryzacją. Dzięki kompaktowej budowie, elastycznemu zasilaniu logiki (1,8–5,5 V) i prostemu sterowaniu świetnie sprawdza się w robotyce, automatyce i projektach hobbystycznych. Pololu 4971
Sterownik silników krokowych, oferujący mikroki aż do 1/256 kroku, co zapewnia wyjątkową precyzję i płynność ruchu. Dzięki prostej obsłudze – wymagającej jedynie dwóch pinów z mikrokontrolera – oraz niskim napięciu pracy (1,8 do 10 V), doskonale nadaje się do energooszczędnych aplikacji mobilnych, robotycznych i DIY. Zintegrowane złącza, diody LED i potencjometr do regulacji prądu ułatwiają prototypowanie i bezpieczną integrację z popularnymi platformami takimi jak Arduino czy ESP32. Adafruit 6353
Pololu Simple High-Power Motor Controller 24v23
Brak towaru
Miniaturowy sterownik ESC silnika bezszczotkowego 7A 1-2S BLheli_S XSD7A to kompaktowe urządzenie o dużej wydajności, idealne do kontroli silników bezszczotkowych w małych projektach. Dzięki niskiej wadze i solidnej mocy, nadaje się do dronów, modeli RC i innych aplikacji wymagających precyzyjnej kontroli silnika.
Brak towaru
Pololu G2 18v15 High Power to miniaturowy sterownik silnika DC. Zasilanie sterownika: 6,5...30 V. Wydajność prądowa modułu: 15 A. Moduł posiada zabezpieczenie przed napięciem wstecznym i przepięciami. Pololu 1363
Pololu Simple High-Power Motor Controller 18v15