- Obecnie brak na stanie
LPY510AL Dual-Axis (Pitch and Yaw or XZ) Gyro with ±100°/s and ±400°/s Ranges
This gyroscope board is a basic carrier/breakout board for the ST LPY510AL dual-axis gyro, which measures the angular rates of rotation about the pitch (x) and yaw (z) axes. Two separate analog voltage outputs for each axis provide angular velocity ranges of ±100°/s and ±400°/s. This board has a 3.3V regulator for easy integration with 5 V parts, includes a low-pass filter on each output for noise reduction, and is smaller than competing products, all at a lower price.
Discontinuation Notice: These dual axis gyros are being replaced by the L3G4200D 3-axis gyro and will be discontinued when stock runs out. They are not recommended for new designs where continued part availability is important.
![]() |
![]() |
These two-axis gyros are essentially carrier boards or breakout boards for ST’s LPR510AL, LPY510AL, LPR550AL, and LPY550AL MEMS (micro-electro-mechanical systems) gyroscopes; we therefore recommend careful reading of the the corresponding datasheets (listed under the “resources” tab) before using these products.
These parts are all members of ST’s latest family of dual-axis gyroscopes that differ only in their sensitivities and axes of rotation. Boards marked with a black X on the bottom silkscreen have ±100°/s and ±400°/s ranges; boards marked with a red X have ±500°/s and ±2000°/s ranges (each chip provides two sensitivities per axis—1x and 4x—and both are brought out to the user I/O on these carrier boards).
Although these are great ICs, their small, leadless packages make them difficult for the typical student or hobbyist to use. They also operate at 2.7 V to 3.6 V, which can make interfacing difficult for microcontrollers operating at 5 V. These carrier boards address both issues while keeping the overall size at half a square inch.
![]() |
The axes of rotation are pitch (x) and roll (y) for LPR5x0AL parts and pitch and yaw (z) for LPY5x0AL parts; the relevant axes are indicated on the board silkscreens (shown above). The LPR versions are particularly well-suited for balancing robots with vertical PC boards since one axis can provide tilt-related information and the other can provide heading information. The LPY version can be used in pairs with one unit perpendicular to the other to make a flat three-axis gyro (this can also be achieved using one LPY and one LPR).
The schematics for the LPR5x0AL and LPY5x0AL gyroscope carriers are shown below. The devices can be powered directly through the Vdd/3.3V pin using a supply that is within the gyro chips’ acceptable power supply range of 2.7 V to 3.6 V. Alternatively, the boards can be powered by higher voltages, up to 16 V, using the VIN pin, which connects to a low-dropout 3.3V regulator. In this configuration, the 3.3V pin can serve as an output to be used as a reference voltage or power source for other low-power devices (up to around 50 mA, depending on the input voltage). Please note that unlike some other gyros and accelerometers, the outputs are not ratiometric with the Vdd/3.3V power line (i.e. at zero rate of rotation, the output should equal Vref, not half of the Vdd/3.3V supply).
The power-down pin is not connected by default. It must be driven low for the gyro to operate. If a low-power state is not required for your application, use a small piece of wire or solder to make a short between the power-down pin and the ground (square) pin next to it. To use the power-down pin, your circuit must bring it up to Vdd (typically 3.3 V); in 5V applications, this can be done by adding a pull-up resistor to the 3.3V output.
The self-test input is pulled low by default. To activate the self-test feature, drive the line to Vdd (the same pull-up trick as above can be used for 5V applications).
![]() |
For 5V microcontroller applications, the power down and self test lines should not be driven high. Instead, the microcontroller I/O pin can emulate an open-drain or open-collector output by alternating between low output and high-impedance (input) states. Put another way, if you are using a 5 V microcontroller, you should make your power down and self test I/O lines inputs and use pull-up to 3.3 V if you want them to be high. It is always safe for you to drive these lines low.
The output is an RC-filtered analog voltage that ranges from 0 to Vdd; with no rotation, the output voltage is typically 1.23 V regardless of Vdd. For 5V applications, the 3.3V output can be used as a reference for analog-to-digital converters to gain full resolution samples. Otherwise, your conversions will be limited to 66% of the full range (e.g. an 8-bit ADC will yield numbers from 0 to 168).
The gyro boards ship with a 1×10 0.1" breakaway male header strip (as shown in the picture to the right) that can be used for connecting custom cables or premium jumper wires or for plugging into perfboards or breadboards.
|
|
![]() |
MMA7361L 3-Axis Accelerometer ±1.5/6g with Voltage Regulator |
![]() |
MMA7361L 3-Axis Accelerometer ±1.5/6g |
![]() |
TB6612FNG Dual Motor Driver Carrier |
Producent
Osoba odpowiedzialna
Zestaw EVALKIT-VL6180X zawiera płytkę startową Nucleo-F401RE z mikrokontrolerem STM32F401 oraz płytkę rozszerzeniową z czujnikiem zbliżenia / gestów VL6180X
Brak towaru
Moduł wyświetlacza TFT 3,2 z touchpanelem i gniazdem kart SD, 40-pinowy
Brak towaru
Wyświetlacz graficzny 128x32; 67,5x25,2mm, typ: COG, FFSTN Negative, Transmissive, 3.3V UC1601, podświetlanie RGB
Brak towaru
Brak towaru
Quectel L70-R to doskonały wybór do projektów wymagających precyzyjnego pozycjonowania przy minimalnym zużyciu energii. Dzięki ultrakompaktowej obudowie, wysokiej czułości i inteligentnym funkcjom zarządzania energią, moduł idealnie sprawdzi się w trackerach GPS, urządzeniach bateryjnych, rozwiązaniach IoT oraz elektronice ubieralnej. To nowoczesne i niezawodne rozwiązanie dla projektów, w których liczy się każdy miliwat i każdy milimetr przestrzeni.
Brak towaru
Brak towaru
Moduł wyświetlacza TFT 2.8", panel dotykowy, cztery przyciski, dedykowany do Raspberry Pi, RoHS
Brak towaru
Ultradźwiękowy czujnik odległości modUS-015 działa w oparciu o analizę opóźnienia odbicia fali ultradźwiękowej od przeszkody - zasięg czujnika od 2 do 400 cm z dokładnością 0.3 cm +1%
Brak towaru
Jednokanałowy inwerter logiczny z wejściem Schmitt Trigger z serii AHC, przeznaczony do pracy w szerokim zakresie napięć 2,0–5,5 V. Obudowa SOT-23 umożliwia montaż SMD w kompaktowych projektach cyfrowych
Brak towaru
MYIR MYC-SAMA5D36 to komputer jednopłytkowy w postaci karty z złączem SO-DIMM 200-pinów. Został wyposażony procesor SAMA5D36 firmy Atmel, oparty na rdzeni Cortex-A5. Może pracować z maksymalną częstotliwością 536 MHz. Posiada 512 MB pamięci DDR2 SDRAM, 256 MB pamięć NAND FLASH. Porty GPIO, interfejsy zostały wyprowadzone na złączu SO-DIMM 200-pinów
Brak towaru
Moduł pamięci Flash eMMC 5.1 dla komputerów Odroid XU3/XU4 firmy Hardkernel. Pojemność 64GB, zainstalowany system operacyjny Linux. W zestawie znajduje się adapter micro-SD. 64GB eMMC module for ODROID-XU3/XU4, Linux
Dostępne do wyczerpania magazynu!
Brak towaru
Moduł pamięci Flash eMMC 5.0 dla komputerów Odroid XU3/XU4 firmy Hardkernel. Pojemność 16GB, zainstalowany system operacyjny Linux. W zestawie znajduje się adapter micro-SD. 16GB eMMC 5.0 Module for ODROID-XU3/XU4, Linux
Brak towaru
Brak towaru
Moduł wyświetlacza TFT 3,2" z touchpanelem, rozdzielczość 320 x 240 pikseli, 34-pinowy, z ikonami na wyświetlaczu
Brak towaru
Brak towaru
Brak towaru
LPY510AL Dual-Axis (Pitch and Yaw or XZ) Gyro with ą100°/s and ą400°/s Ranges