- Obecnie brak na stanie

Pololu RC Servo Multiplexer 4 Channel (partial kit)
This compact device serves as a four-channel multiplexer of hobby radio control pulses, allowing easy switching between two independent signal sources. A fifth channel selects whether the output is from the master or the slave source: a pulse width below the threshold selects the master channels, while a longer pulse width selects the slave channels. This version is a partial kit.
![]() |
The Pololu RC servo multiplexer can be used with standard hobby radio control systems and servo controllers to allow easy switching of servo control between two independent sources using a fifth channel as the output selector. This makes it ideal for applications in which you have two possible control sources and want to be able to switch between them on the fly. For example, you could connect two RC receivers to the same set of servos (or similar devices, such as RC-based motor controllers) and allow the master transmitter to decide whether the master or slave transmitter is in control, thereby setting up your own buddy-system training setup. Another possible application would involve multiplexing between an RC receiver and a servo controller, which would allow you to switch between autonomous and manual control of a set of servos.
![]() |
The pins on the multiplexer allow for easy connecting to servo cables: the column along the outside edge of the board is ground, the column in the middle is power (which must be supplied by the master), and the interior column is the signal. The pin spacing is 0.100". This multiplexer is available as an assembled version with male header pins soldered in or as a partial kit. The male headers can be used with standard servo connectors; the kit provides additional flexibility and compactness by allowing wires to be soldered directly to the board, as shown in the picture to the right. The kit version ships with three 13×1 male header strips, a 2×1 male header strip, and a blue shorting block.
The power supplied by the master should be between 2.5 and 15 V, and it must be capable of supplying the current that the servos connected to the outputs draw. The logic voltage used on the multiplexer board will be regulated to 5 V if the supply voltage is greater than 5 V; otherwise, it will be approximately equal to the supply voltage. Note that the master and slave signal voltages must not exceed this logic voltage.
Pins S1 through S4 comprise the four slave input signals and pins M1 through M4 comprise the four master input signals. Pins OUT1 through OUT4 are the multiplexed outputs, and their source is determined by the signal on the SEL pin. If the selection pulse width is below the 1.6 ms threshold, OUT1 through OUT4 output the signals on M1 through M4, respectively (i.e. the master source is output); otherwise, OUT1 through OUT4 output the signals on S1 through S4, respectively (i.e. the slave source is output). Note that there is approximately ±0.1 ms of hysteresis on the threshold, meaning that the pulse width will have to get to approximately 1.7 ms before the slave signals become the output, and once this happens, the signal will have to fall below 1.5 ms before the master signals become the output.
If the selection signal is invalid, an optional jumper across the pins labeled J1 determines the output behavior. If the jumper is left off, the output channels go low and stay low for as long as the signal on the SEL pin remains invalid. For many servos and electronic speed controls (ESCs), a constant low on the signal line will turn them off, which might be desirable if the control signals are known to be bad. If the jumper is in place, the output channels default to the master signals if the selection signal becomes invalid. The multiplexer considers a valid RC signal to have a 10 – 100 Hz pulse rate and a 0.5 – 2.5 ms pulse width.
The board has three indicator LEDs. If the outputs come from the master, only the green LED will be lit; if the outputs come from the slave, the yellow LED will be lit; if the outputs are turned off (all low) because of an invalid selector signal, the red and green LEDs will be lit.
Producent BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Osoba odpowiedzialna BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Moduł kamery 18 Mpx z sensorem AR1820HS współpracujący z Raspberry Pi. Oferuje rozdzielczość wideo do 4912x3684 pikseli przy 15 fps. ArduCAM B0164
Brak towaru
Najpopularniejsze spoiwo lutownicze Sn60Pb40 SW26 to wysokiej jakości ołowiowy produkt z topnikiem SW26, przeznaczony do profesjonalnego lutowania w elektronice i elektrotechnice, spełniający normę EN ISO 9453:2014
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Nowa wersja popularnego kontrolera inteligentnych ubrań FLORA firmy Adafruit (45 mm średnicy; 4,4 g) z mikrokontrolerem ATmega32U4, kontroler jest kompatybilny z Arduino. Płytka przystosowana jest do przyszywania do tkanin. Adafruit 659
Brak towaru
Brak towaru
Brak towaru
Kamera o rozdzielczości 5 MPx z interfejsem USB. Wyposażona w sensor CMOS OV5648 z szerokokątnym obiektywem o kącie widzenia 90°. ArduCAM UB0233
Brak towaru
Brak towaru
Brak towaru
Zestaw AVT do samodzielnego montażu centralki alarmowej. AVT5466 B
Brak towaru
Brak towaru
Obiektyw z mocowaniem C-Mount. Ogniskowa o długości 5 mm, FoV 60.3°(H), 47.1°(V), manualny focus i regulowana przysłona. Przeznaczony do współpracy z kamerą Raspberry Pi HQ. ArduCAM LN042
Brak towaru
Pololu RC Servo Multiplexer 4 Channel (partial kit)