- Obecnie brak na stanie
Passive Infrared (PIR) Detector SE-10
The passive infrared detector (PID) motion sensor SE-10, also called a passive infrared (PIR) sensor, detects movement of infrared light sources at 7 to 14 µm. People emit infrared radiation from 8 to 14 µm, which makes this an excellent sensor for detecting human movement. Two infrared detector “pixels” allow the detector to filter out changes affecting the whole sensing area, like weather or light.
![]() |
| PIR motion sensor SE-10 top view. |
|---|
The SE-10 passive infrared detector senses motion of infrared light sources at the same wavelengths humans emit. Passive infrared detectors like the SE-10 are used in security and automation applications. In security, motion sensors are integrated into alarm systems and used to turn on security cameras. PIR motion detectors are also used to automatically turn on lights when people enter a room.
The two pyroelectric sensing elements allow the SE-10 IR motion detector to see moving infrared light sources while ignoring changes in background infrared radiation. A lens focuses the infrared light on to the two 2?1 mm silicon coated sensing elements spaced 1 mm apart.
When the sensor is powered on, it takes 1-2 seconds to calibrate itself to the background infrared radiation before it can detect motion. After calibration, the detector drives the open-collector Alarm pin low for the duration of the sensed motion (the alarm pin state is not latched); when there is no motion detected, the alarm pin is floating. The open-collector setup allows multiple motion sensors to be connected on a single input pin, but it means that you will need an external pull-up resistor on the alarm pin. If any of the motion sensors go off, the input pin will be pulled low.
The red wire is power (5 to 12V), brown wire is GND, and black wire is an open-collector signal (Alarm) that requires an external pull-up. This sensor works from 5 to 12 V (datasheet shows 12 V). You can also install a jumper wire past the 5 V regulator on board to make this unit work at 3.3 V. The sensor draws 1.6 mA at 3.3 V.
The connector is slightly odd but has a 0.1" pitch female connector making it compatible with jumper wires and 0.1" male headers.
![]() |
Pololu Carrier with Sharp GP2Y0D810Z0F Digital Distance Sensor 10cm |
![]() |
Mini Pushbutton Switch: PCB-Mount, 2-Pin, SPST, 50mA (5-Pack) |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack |
Producent
Osoba odpowiedzialna
Zestaw AVT do samodzielnego montażu miniaturowego sterownika taśmy LED. AVT1847 B
Brak towaru
Zmontowany miniaturowy sterownik taśmy LED. AVT1847 C
Brak towaru
PCB i zaprogramowany układ do programowanego sterownika LED. AVT1881 A+
Brak towaru
Zestaw AVT do samodzielnego montażu programowanego sterownika LED. AVT1881 B
Brak towaru
Zestaw AVT do samodzielnego montażu sterownika zasilania taśm LED z wyłącznikiem czasowym. AVT1867 B
Brak towaru
Zmontowany sterownik zasilania taśm LED z wyłącznikiem czasowym. AVT1867 C
Brak towaru
PCB i zaprogrmowany układ do sterownika oświetlenia LED sterowanego dowolnym pilotem. AVT3133 A+
Brak towaru
Zestaw AVT do samodzielnego montażu sterownika oświetlenia LED sterowanego dowolnym pilotem. AVT3133 B
Brak towaru
Zmontowany sterownik oświetlenia LED sterowany dowolnym pilotem. AVT3133 C
Brak towaru
PCB i zaprogramowany układ do 3-osiowego generatora CNC. AVT5422 A+
Brak towaru
Zestaw AVT do samodzielnego montażu 3-osiowego generatora CNC. AVT5422 B
Brak towaru
Zmontowany 3-osiowy generator CNC. AVT5422 C
Brak towaru
Przewód USB o długości 1m, służący do transmisji danych i ładowania urządzeń ze złączem microUSB. We wtyczce przewodu wbudowano miernik, pozwalający na oszacowanie poboru prądu przez dołączone urządzenie i odczytanie wartości napięcia zasilającego
Brak towaru
Orange Pi Lite to komputer z SoC Alwinner H3 (4 rdzenie, Cortex-A7, Mali400MP2 GPU), ma 512 MB pamięci RAM oraz moduł WiFi 802.11 b/g/n. Dostępne są dwa porty USB 2.0, jak i jeden port USB OTG, złącze GPIO 40-pin oraz gniazdo kart micro-SD. W zestawie znajduje się antena do Wi-Fi
Brak towaru
Orange Pi Plus 2e to komputer z SoC Alwinner H3 (4 rdzenie, Cortex-A7, Mali400MP2 GPU), ma 2 GB pamięci RAM, 16GB zintegrowanej pamięci eMMC oraz moduł WiFi 802.11 b/g/n. Dostępne są trzy porty USB 2.0, port ethernet (1 Gigabit), złącze GPIO 40-pin oraz gniazdo kart micro-SD
Brak towaru
Orange Pi PC Plus to komputer z SoC Alwinner H3 (4 rdzenie Cortex-A7, Mali400MP2 GPU), Wi-Fi, 1 GB RAM, 100 Mb Ethernet oraz 8GB pamięci eMMC. Dostępne są 3 porty USB 2.0, port USB OTG, złącze GPIO 2x20 kompatybilne z Raspberry Pi 2 oraz gniazdo kart micro-SD
Brak towaru
Passive Infrared (PIR) Detector SE-10