- Out-of-Stock
Passive Infrared (PIR) Detector SE-10
The passive infrared detector (PID) motion sensor SE-10, also called a passive infrared (PIR) sensor, detects movement of infrared light sources at 7 to 14 µm. People emit infrared radiation from 8 to 14 µm, which makes this an excellent sensor for detecting human movement. Two infrared detector “pixels” allow the detector to filter out changes affecting the whole sensing area, like weather or light.
![]() |
| PIR motion sensor SE-10 top view. |
|---|
The SE-10 passive infrared detector senses motion of infrared light sources at the same wavelengths humans emit. Passive infrared detectors like the SE-10 are used in security and automation applications. In security, motion sensors are integrated into alarm systems and used to turn on security cameras. PIR motion detectors are also used to automatically turn on lights when people enter a room.
The two pyroelectric sensing elements allow the SE-10 IR motion detector to see moving infrared light sources while ignoring changes in background infrared radiation. A lens focuses the infrared light on to the two 2?1 mm silicon coated sensing elements spaced 1 mm apart.
When the sensor is powered on, it takes 1-2 seconds to calibrate itself to the background infrared radiation before it can detect motion. After calibration, the detector drives the open-collector Alarm pin low for the duration of the sensed motion (the alarm pin state is not latched); when there is no motion detected, the alarm pin is floating. The open-collector setup allows multiple motion sensors to be connected on a single input pin, but it means that you will need an external pull-up resistor on the alarm pin. If any of the motion sensors go off, the input pin will be pulled low.
The red wire is power (5 to 12V), brown wire is GND, and black wire is an open-collector signal (Alarm) that requires an external pull-up. This sensor works from 5 to 12 V (datasheet shows 12 V). You can also install a jumper wire past the 5 V regulator on board to make this unit work at 3.3 V. The sensor draws 1.6 mA at 3.3 V.
The connector is slightly odd but has a 0.1" pitch female connector making it compatible with jumper wires and 0.1" male headers.
![]() |
Pololu Carrier with Sharp GP2Y0D810Z0F Digital Distance Sensor 10cm |
![]() |
Mini Pushbutton Switch: PCB-Mount, 2-Pin, SPST, 50mA (5-Pack) |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
No product available!
No product available!
No product available!
No product available!
No product available!
Industrial DTU 4G module with Qualcomm SIM7600E-H chip. It allows you to connect industrial modules with serial communication via RS232, RS485 or TTL interfaces with 4G networks. Waveshare SIM7600E-H 4G DTU (EU)
No product available!
Camera with a resolution of 5 MPx with a USB interface. Equipped with a CMOS OV5648 sensor with a wide-angle lens with a viewing angle of 140°. ArduCAM U6073
No product available!
No product available!
No product available!
No product available!
No product available!
Convenient to use retractable 3in1 USB cable with USB A plug and three output connectors: microUSB, USB Type C and Lightning
No product available!
Camera for Odroid C1 / C1 + / C2 / C0 / XU4 computers with 720p quality with USB 2.0 interface. It runs under the control of Linux and Android 4.2.2 and above
No product available!
DSLR SHUTTER ELECTRONIC DRAIN HOSE FOR CAMERA - SHEET PRINTED AND PROGRAMMED UK? ADVERTISING
No product available!
No product available!
No product available!
Passive Infrared (PIR) Detector SE-10