List of products by brand Sparkfun

The board with the RP2040 microcontroller equipped with two ARM Cortex-M0 + cores, which work at a frequency of 133 MHz, 256 kB RAM. The board also has 16 MB of QSPI flash memory. The system can be programmed in C/C++ or microPython. SparkFun DEV-17745

Soil moisture sensor with I2C interface. The probe has two pointed tabs, making it easy to insert into the ground. The sensor is supplied with the voltage of 3.3 V or 5 V. SparkFun SEN-17731

Module with digital barometer BMP581. It enables pressure measurement in the range from 300 to 1250 hPa with an accuracy of ± 5 Pa and communicates via I2C or SPI. SparkFun SEN-20170

SEN-13676

MicroMod main module with iMXRT1062 microcontroller. Equipped with an M.2 connector, it can work with MicroMod expansion boards. SprakFun DEV-16402

Love To Code Chibi Chip is an educational module for learning programming designed for beginners of all ages and levels who want to start learning programming without installing software. DEV-14591, Adafruit 3674

Prototype board designed to cooperate with Particle Photon. The board has prototype holes with a 2.54 mm pitch and pins of the I2C interface. SparkFun DEV-13598

Digital gas sensor solution that senses a wide range of Total Volatile Organic Compounds (TVOCs), including equivalent carbon dioxide (eCO2) and metal oxide (MOX) levels, intended for indoor air quality monitoring in personal devices such as watches and phones, but we’ve put it on a breakout board so you can use it as a regular I2C device. SEN-14193

Prototype board designed to work with Alchitry Au and Alchitry Cu. There are prototype holes on the board with a 2.54 mm raster connected to the board connectors. SparkFun DEV-16524

Power supply module with an input voltage from 6 to 12 V and a configurable output voltage of 3.3 V or 5 V. It has holes with a 2.54 mm pitch. Perfect for use with a breadboard. SparkFun PRT-13032

Simple-to-use, open source solution for measuring weight and temperature with the ability to read multiple types of load cells and offers a simple-to-use serial menu to configure calibration value, sample rate, time stamp and units of precision. SEN-13261

A development board that uses the ESP32-C3 chip based on the RISC-V architecture. It has built-in 400 KB of SRAM and 4 MB of Flash memory and a clock frequency of 160 MHz. Pro Micro offers a Qwiic connector that allows you to connect any sensor that communicates via the I2C bus. SparkFun DEV-23484

Flexible 4-core cable, 500 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17257

Cable dedicated to MyoWare 2.0 muscle tension sensors. It allows you to connect the electrode with the plate in the event that it must be located at a distance from the sensor. SparkFun CAB-19244

The SST Liquid Level Sensor provides single point liquid detection via a TTL compatible push/pull output. This optical liquid level sensor features a miniature design that allows for installation in areas where space is limited. SEN-13835

Module with digital temperature sensor AS6212. It enables measurement in the range from –40°C to 125°C with an accuracy of 0.2°C. SparkFun SEN-18521

BOB-13263

Module with 3.5 mm TRS connector for MyoWare 2.0 muscle tension sensors. It allows you to conveniently connect the sensors with the development board via the Arduino shield. SparkFun DEV-18425

The SparkFun OpenLog is an open source data logger that works over a simple serial connection and supports microSD cards up to 64GB. DEV-13712

Module with an AB class amplifier based on the Boomer® LM4853 system. It can work in two modes: mono (power 1.5 W, load 4 Ω) or stereo (power 300 mW, load 8 Ω). It has a potentiometer for power control and gain control for the left and right channel. SparkFun DEV-14475