LIDAR distance sensor with a measuring range from 5 cm to 10 m and a resolution of 1 cm. It was made of high-quality optical and electronic devices that ensure stability, high sensitivity and precision. Thanks to this, the sensor is perfect for drones or other unmanned applications. It is resistant to disturbances from temperature, humidity, light and air flow. A laser beam with a wavelength of 940 nm is used for the measurement. The measurement angle is 4.77°. The sensor is based on the nRF52840 chip and allows users to create their own dedicated software. The module communicates via the I2C or ANT interface and is powered by 5 V. The sensor is available with the Arduino library and the ANT library for easy operation and commissioning.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Range finder with a measuring range up to 12m. The current consumption is up to 120mA and the supply voltage 4.5 ... 6V. Communication via the UART interface. DFRobot SEN0259
Recognizes the distance of an object away from the sensor up to about 10 inches (~25cm) and the location of the object from side to side across the sensor in about a 6 inch (~15cm) span. You will be able to use I2C or UART to communicate with the ZX Sensor via an Arduino-based microcontroller as well as a computer. SEN-12780
No product available!
KAmodVL6180X is a module that allows to measure light intensity (ALS), distance to the object and recognition of gesture. It has an embedded voltage regulator and voltage level translators on signal lines. Thanks to this can be used in systems with 2.8...5.5V power supply voltage.
The GP2Y0A60SZ offers a wide detection range of 4″ to 60″ (10cm to 150cm) and a high update rate of 60Hz. The distance is indicated by analog voltage - only a single analog input is required to interface with the module. Pololu 2476
Suitable for outdoor applications such as car reversing sensors, security alarms, industrial inspection, etc. SEN0207
This sensor is a carrier/breakout board for ST’s VL53L0X laser-ranging sensor, which measures the range to a target object up to 2 m away.
This module features a fixed-gain, 38 kHz modulated IR sensor and a corresponding IR LED with oscillator circuit to make a tiny proximity sensor.
No product available!
This module features a fixed-gain, 38 kHz modulated IR sensor and a corresponding IR LED with oscillator circuit to make a tiny proximity sensor. This low-brightness version draws an average of 8 mA at 5 V and has a typical sensing range up to approximately 12 inches (30 cm).
Adafruit VL53L0X Time of Flight Distance Sensor is a laser distance sensor using the ToF (Time of Flight) measurement technique. The module is powered by 2.8 ... 5V voltage and can measure up to 1000mm. Adafruit 3317
ToF distance sensor module based on the VL6180X system. It offers a range of up to 10 cm and communicates via the I2C interface. Adafruit 3316
No product available!
Laser rangefinder with measuring range up to 22m. The current consumption is up to 200mA and the supply voltage 4.5 ... 6V. Communication via UART or CAN interface. DFRobot SEN0238
A multifunctional module with an optical sensor for measuring the intensity of illumination, the color of the incident RGB light, the distance from the object and the detection of 3D gestures. Adafruit 3595
LIDAR distance sensor with a measuring range from 5 cm to 10 m and a resolution of 1 cm. It communicates via the I2C or ANT interface. SparkFun SEN-15776