Module with IPS LCD display, 1.14" diagonal and 240x135 px resolution. Communication via SPI interface. SB Components 21512
List of products by brand SB-Components
There are 99 products.
GNSS module based on the L76B chip that can work with GPS, BDS and QZSS systems. Communication via a UART interface. SB Components 24056
Module with PMSA003 air quality sensor and BME280 pressure sensor designed for Raspberry Pi Pico. It is equipped with WiFi ESP8266 communication. SB Components 22342
Open source USB dongle that allows you to work with the LoRa network. It allows you to communicate with a range of up to 5 km and has a built-in 1.14-inch LCD display. SB Components 23004
LoRa module working on the 868 MHz frequency band with built-in RP2040 microcontroller, CH340 USB to UART converter, 74HC125V voltage level converter. SB Components 23240
Expansion board with LoRa E22-400T22S module for Raspberry Pi. It supports the LoRaWAN protocol and allows communication in the 433 MHz frequency band. SB Components 22564
1-channel module with a relay designed to work with the Raspberry Pi Pico. It can switch signals up to 250 V AC and 7 A or 30 V DC and 10 A. SB Components 21277
UPS uninterruptible power supply module for Raspberry Pi, allowing the microcomputer to continue working and shut down safely after a power failure. Uninterruptible power supply included. SB Components UPS HAT
The PMSA003 air quality sensor module to work with the Raspberry Pi Pico. It allows for a analysis of the amount of pollutants in the environment based on the concentration of PM1.0, PM2.5 and PM10 particles. SB Components 21819
The expansion board with the LoRa E22-900T22S module for the Raspberry Pi Pico. It supports the LoRaWAN protocol and enables communication in the 868 MHz frequency band. SB Components 21628
Development board with RP2040 and ESP-12E microcontroller. Equipped with 0.91" OLED display. SB Components 24186
The expansion board with the LoRa E22-400T22S module for the Raspberry Pi Pico. It supports the LoRaWAN protocol and allows communication in the 433 MHz frequency band. SB Components 21642
A pin expander designed for Raspberry Pi Pico boards. It is equipped with a standard female connector and four sets of male strips 2x20 pins. SB Components 21352
Module with a differential pressure sensor based on the MPXV5010DP system. It uses a 22-bit ADC and allows the measurement of the pressure difference between two inlets in the range of up to 10 kPa. Comes with a soldered Raspberry Pi Pico W board. SB Components 26173
2-channel module with relays designed to work with the Raspberry Pi Pico. It can switch signals up to 120 V AC or 24 V DC and currents up to 2 A. SB Components 21376
A small module with a 1.54" LCD display and a resolution of 240x240 pixels, equipped with a WiFi ESP-12E module. It is programmed via a USB type C connector. SB Components 25626
Adapter designed for micro:bit educational modules. It facilitates access to all pins, which are led out on the connector with a raster of 2.54 mm, which allows the use of a breadboard. SB Components 14880
Adapter designed for Raspberry Pi minicomputers. It facilitates access to all pins, which are led out on the connector with a raster of 2.54 mm, which allows the use of a breadboard. SB Components 14927
The board with prototype holes is dedicated to the Raspberry Pi Pico. It offers an area of 6x20 holes and two areas of 8x20 holes with a pitch of 2.54 mm with marked pin labels. SB Components 21505
A module with a barcode and QR scanner designed to work with the Raspberry Pi Pico. It allows you to read one-dimensional and two-dimensional codes using the intelligent image recognition algorithm. SB Components 22441