- Obecnie brak na stanie
Pololu Pushbutton Power Switch LV
The Pololu Pushbutton Power Switch is a patented design initially created for our Orangutan Robot Controllers as an alternative to bulky mechanical switches. The switch is intended to be the main power switch for a DC device requiring up to several amps of current. Please see the detailed description for product details and limitations. This item is the 2.5-7.0 V low-voltage version.
Note: The Pololu Pushbutton Power Switch is available in two voltage versions: standard voltage, 4.5-20 V and low voltage, 2.5-7.0 V. Please be sure to select the correct unit for your application.
![]() |
The Pololu Pushbutton Power Switch is a compact, solid-state power switch controlled by a momentary pushbutton switch. Because the switched current does not flow through the mechanical switch, a large variety of small, low-power switches can be used to control a substantial amount of power. The use of momentary pushbutton switches also allows multiple switches to be used in parallel to control the power to one load. The solid-state switch also allows the load to turn off its own power, which can be beneficial when used with battery chemistries sensitive to over-discharging. Please note that this switch has several drawbacks when compared to mechanical switches, so please be sure you fully understand this product before using it in your system.
The Pololu Pushbutton Power Switch works well in its intended application as a DC power switch for small robots, but because it is fundamentally different from a mechanical power switch, the benefits and drawbacks of the components must be fully considered.
Benefits over mechanical switches:
Drawbacks compared to mechanical switches:
![]() |
| Pololu Pushbutton Power Switch on a solderless breadboard. |
|---|
The Pololu Pushbutton Power Switch can fit in an 18-pin DIP (dual in-line package) footprint, making it compatible with solderless breadboards and perforated printed circuit boards with standard 0.1" spacing. For such applications, the included male header pins can be soldered to the switch PCB as shown in the picture to the right. Alternatively, wires can be soldered directly to the switch PCB for non-breadboard applications. For high-current applications, make sure that the wires can safely carry the current. Two pads/pins are provided for each of the power nodes, and multiple pads should be used for applications drawing over 5 A.
The included pushbutton switch can be used to trigger the switch. Alternatively, a separate pushbutton, such as a remote panel-mounted unit, can be used instead. Multiple pushbuttons can be wired in parallel for multiple control points, and each of the parallel pushbuttons will be able to turn the switch on or off. The latching circuit performs some button debouncing, but pushbuttons with excessive bouncing (several ms) might not function well with this product.
The Pololu Pushbutton Power Switch has two main components: a P-channel power MOSFET that switches the load current and a latching circuit that controls the gate of the MOSFET.
![]() |
| Pololu Pushbutton Power Switch block diagram. |
|---|
The overall switch performance is determined by the MOSFET characteristics, which are specified in their datasheets. The standard voltage version uses the FDS6679AZ (421k pdf); the low-voltage version uses the FDS4465 (141k pdf). The latching circuit is designed to operate over a wide range of voltages and to draw very little current in the off state (typically under 0.01 ěA). In the on state, the switch pulls the MOSFET gate to within 0.2 V of ground so that the MOSFET’s Vgs can be approximated as the supply voltage.
![]() |
| Pololu Pushbutton Power Switch OFF input detail. |
|---|
The latching circuit controlling the power MOSFET includes an OFF input that can be used by the target device to shut off its own power. The internal structure of this input is shown to the right. Applying more than approximately 1 V to the OFF pin will cause the power switch to turn off. The maximum voltage for the OFF pin is 30 V independent of the switch voltage (VIN).
The switch operating range is limited by the ability to change state reliably. At low voltages, the switch is difficult to turn on, and the switch will turn itself off once the voltage falls far enough (typically 3 V and 1.5 V for the SV and LV versions, respectively). At high voltages, the switches become difficult to turn off. The reliability of turning off is affected by a combination of the supply voltage, the amount of bouncing on the pushbutton switch, and the amount of noise on the supply line. For applications at the high end of the operating range, tests should be performed to ensure that the device can properly turn off.
![]() |
Pololu 5V Boost Regulator NCP1402 |
![]() |
Pololu Pushbutton Power Switch SV |
![]() |
Pololu Adjustable Boost Regulator 2.5-9.5V |
Producent
Osoba odpowiedzialna
Crowtail – BME280 Atmospheric Sensor 2.0 to wielofunkcyjny czujnik środowiskowy mierzący temperaturę, wilgotność i ciśnienie, z interfejsem I2C i niskim poborem prądu. Znajduje zastosowanie w aplikacjach pogodowych, domowej automatyce i systemach mobilnych.
Brak towaru
Crowtail – GP02 GPS/BDS/GNSS to kompaktowy moduł lokalizacyjny z obsługą trzech systemów nawigacyjnych, dokładnością poniżej 2 m i interfejsem UART. Stosowany w projektach wymagających precyzyjnego pozycjonowania w czasie rzeczywistym, takich jak rejestratory danych, lokalizacja pojazdów i urządzenia terenowe.
Brak towaru
Crowtail – Dual Coil Latching Relay Module 2.0 to energooszczędny, dwukanałowy przekaźnik bistabilny, który zachowuje stan po zaniku zasilania. Przeznaczony do zastosowań w systemach automatyki, zdalnego sterowania i projektach zasilanych bateryjnie.
Brak towaru
Crowtail-Tilt Switch 2.0 to prosty czujnik cyfrowy wykrywający zmianę położenia modułu w osi pion–poziom. Stosowany w projektach wymagających detekcji przechyłu, sygnalizacji orientacji lub aktywacji w zależności od pozycji.
Brak towaru
Kompaktowy transceiver LoRa oparty na ESP32-S3, oferujący stabilną komunikację terenową bez potrzeby korzystania z sieci komórkowej. Urządzenie wyposażono w preinstalowane Meshtastic, wyświetlacz OLED 1,3” oraz transceiver SX1262 obsługujący pasma EU868 MHz. Wbudowana bateria 1000 mAh zapewnia długą pracę, a obsługa Bluetooth i USB-C ułatwia konfigurację oraz codzienne użytkowanie. Elecrow ThinkNode M2 Walkie-Talkie Mini
Brak towaru
Filament PLA (Opal Green) o średnicy 1,75 mm i masie 1 kg, produkowany przez Prusa Research z tolerancją średnicy ±0,02 mm, przeznaczony do precyzyjnego druku 3D modeli i prototypów. Prusa Research
Brak towaru
Filament PETG (czarny) o średnicy 1,75 mm i masie 1 kg, produkowany przez Prusa Research z tolerancją średnicy ±0,02 mm, przeznaczony do drukarek 3D FDM.
Brak towaru
Filament PETG (czarny) o średnicy 1,75 mm i masie 1 kg, produkowany przez Prusa Research z tolerancją średnicy ±0,02 mm, przeznaczony do drukarek 3D FDM. Prusa Research
Brak towaru
Filament PETG (Anthracite Grey) o średnicy 1,75 mm i masie 1 kg, produkowany przez Prusa Research z tolerancją średnicy ±0,02 mm, przeznaczony do drukarek 3D FDM. Prusa Research
Brak towaru
Filament PETG w kolorze Signal White o średnicy 1,75 mm i masie 1 kg, produkowany przez Prusa Research z tolerancją średnicy ±0,02 mm, przeznaczony do drukarek 3D FDM
Brak towaru
Filament PLA (Galaxy Silver) o średnicy 1,75 mm i masie 1 kg, produkowany przez Prusa Research z tolerancją średnicy ±0,02 mm, przeznaczony do drukarek 3D FDM
Brak towaru
Filament Prusament PLA w kolorze Gravity Grey o średnicy 1,75mm, przeznaczony do drukarek 3D FDM, produkowany przez Prusa Research z kontrolą parametrów na całej długości szpuli
Brak towaru
Filament PLA (Vanilla White) o średnicy 1,75 mm i masie 1 kg, produkowany przez Prusa Research z tolerancją średnicy ±0,02 mm, przeznaczony do drukarek 3D FDM. Prusa Research
Brak towaru
Filament PLA w kolorze Azure Blue o średnicy 1,75 mm i masie 1 kg, produkowany przez Prusa Research z tolerancją średnicy ±0,02 mm, przeznaczony do drukarek 3D FDM
Brak towaru
Filament PLA w kolorze Army Green o średnicy 1,75 mm i masie 1 kg, produkowany przez Prusa Research z tolerancją średnicy ±0,02 mm, przeznaczony do drukarek 3D FDM
Brak towaru
CH9101R zapewnia konwersję USB–UART w kompaktowej obudowie QSOP16, oferując szeroki zakres prędkości transmisji oraz pełną obsługę sygnałów sterujących. Układ znajduje zastosowanie w adapterach USB–UART, interfejsach komunikacyjnych RS232 i RS485 oraz w modernizacji urządzeń wykorzystujących klasyczny port szeregowy. Dzięki elastycznemu zasilaniu linii I/O ułatwia integrację z nowoczesnymi mikrokontrolerami i systemami wbudowanymi
Brak towaru
Pololu 751 - moduł wyłącznika zasilania z przyciskiem chwilowym - pozwala na włączanie i wyłączanie obciążenia naciśnięciem przycisku, eliminując wady przełączników mechanicznych.