- Obecnie brak na stanie
This semiconductor gas sensor detects the presence of combustible gas and smoke at concentrations from 300 to 10,000 ppm. The sensor’s simple analog voltage interface requires only one analog input pin from your microcontroller.
![]() |
This flammable gas and smoke sensor detects the concentrations of combustible gas in the air and ouputs its reading as an analog voltage. The sensor can measure concentrations of flammable gas of 300 to 10,000 ppm.The sensor can operate at temperatures from -20 to 50°C and consumes less than 150 mA at 5 V. Please read the MQ2 datasheet (184k pdf) for more information about the sensor.
![]() |
| Gas sensor with metal case bottom view. |
|---|
Connecting five volts across the heating (H) pins keeps the sensor hot enough to function correctly. Connecting five volts at either the A or B pins causes the sensor to emit an analog voltage on the other pins. A resistive load between the output pins and ground sets the sensitivity of the detector. Please note that the picture in the datasheet for the top configuration is wrong. Both configurations have the same pinout consistent with the bottom configuration.The resistive load should be calibrated for your particular application using the equations in the datasheet, but a good starting value for the resistor is 20 kΩ.
We offer two breakout boards that make it easier to interface with these sensors: a Pololu carrier board and a SparkFun carrier board. The Pololu version is shown below.
|
![]() |
Pololu MQ Gas Sensor Carrier |
![]() |
Carbon Monoxide Gas Sensor MQ-7 |
![]() |
Alcohol Gas Sensor MQ-3 |
Producent BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Osoba odpowiedzialna BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Moduł ekspandera portów IO oparty na układzie MCP23008. Idealnie pasuje do wyświetlaczy alfanumerycznych LCD 16x2 oraz 20x4 znaki, stając się konwerterem. Adafruit 292
Brak towaru
Zestaw startowy zawierający Raspberry Pi 4B 2 GB oraz wszystkie niezbędne akcesoria: kartę pamięci microSD 32 GB z systemem Rasberry Pi OS, linijkę, przewód Ethernet oraz oficjalne akcesoria: obudowę, zestaw chłodzący, zasilacz i przewód HDMI
Brak towaru
Brak towaru
Filament firmy ROSA3D wykonany z wysokiej jakości granulatu PLA. Na szpuli nawinięte jest 0,8 kg filamentu o średnicy 1,75 mm. ROSA3D PLA Starter Red Jasper Satin
Brak towaru
ACS711 Current Sensor Carrier -25 to +25A
Brak towaru
Zestaw AVT do samodzielnego montażu uniwersalnego sterownika silnika krokowego. AVTY3225 B
Brak towaru
Brak towaru
Moduł z czujnikiem temperatury LM75 frimy NXP dla komputera Banana PI. Czujnik ma rozdzielczość 0,125 st. C. Nazwa producenta: Banana PI - LM75 Temperature Sensor Module
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Zestaw uruchomieniowy z mikrokontrolerem AVR ATtiny2313
Brak towaru
Załogowy Łazik Marsjański od UGEARS to wyjątkowy model, który przenosi marzenia o podboju kosmosu do rzeczywistości, zapewniając nie tylko rozrywkę, ale i cenną wiedzę o przeszłych, obecnych i przyszłych misjach kosmicznych. UGears 70206
Brak towaru
Brak towaru
Generic Linear Actuator with Feedback: 8" Stroke, 12V, 0.6"/s
Brak towaru
Płyn do czyszczenia płytek drukowanych na bazie alkoholu izopropylowego, doskonale usuwa resztki polutownicze, jak również smary i oleje.
Brak towaru