- Obecnie brak na stanie
![Pololu 1634 - Alcohol Gas Sensor MQ-3 Pololu 1634 - Alcohol Gas Sensor MQ-3](https://kamami.pl/8868-large_default/pololu-1634-alcohol-gas-sensor-mq-3.jpg)
Alcohol Gas Sensor MQ-3
darmowa wysyłka na terenie Polski dla wszystkich zamówień powyżej 500 PLN
Jeśli Twoja wpłata zostanie zaksięgowana na naszym koncie do godz. 11:00
Każdy konsument może zwrócić zakupiony towar w ciągu 14 dni bez zbędnych pytań
Alcohol Gas Sensor MQ-3
This semiconductor gas sensor detects the presence of alcohol gas at concentrations from 0.04 mg/L to 4 mg/L, a range suitable for making a breathalyser. The sensor’s simple analog voltage interface requires only one analog input pin from your microcontroller.
![]() |
This alcohol gas sensor detects the concentration of alcohol gas in the air and ouputs its reading as an analog voltage. The concentration sensing range of 0.04 mg/L to 4 mg/L is suitable for breathalysers (the legal limit of breath alcohol concentration, or BrAC, in most US states is 0.08 grams per 210 liters, or 0.38 mg/L). The sensor can operate at temperatures from -10 to 50°C and consumes less than 150 mA at 5 V. Please read the MQ3 datasheet (153k pdf) for more information about the sensor.
![]() |
Gas sensor with orange plastic case bottom view. |
---|
Connecting five volts across the heating (H) pins keeps the sensor hot enough to function correctly. Connecting five volts at either the A or B pins causes the sensor to emit an analog voltage on the other pins. A resistive load between the output pins and ground sets the sensitivity of the detector. Please note that the picture in the datasheet for the top configuration is wrong. Both configurations have the same pinout consistent with the bottom configuration.The resistive load should be calibrated for your particular application using the equations in the datasheet, but a good starting value for the resistor is 200 kΩ.
We offer two breakout boards that make it easier to interface with these sensors: a Pololu carrier board and a SparkFun carrier board. The Pololu version is shown below.
|
Note: These sensors could have orange or blue plastic cases. There is no functional difference between the two colored cases.
|
|
![]() |
Pololu MQ Gas Sensor Carrier |
![]() |
Flammable Gas & Smoke Sensor MQ-2 |
![]() |
Carbon Monoxide Gas Sensor MQ-7 |
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Silnik z plastikową przekładnią 200:1, wałem wyjściowym pod kątem 90°, napięciem pracy 6 V, poborem prądu od 0,07 A do 0,8 A, prędkością 51 RPM i maksymalnym momentem obrotowym 7,2 kg*cm. Pololu 1120
Brak towaru
Wyświetlacz LCD 2x16, 80x36mm, mocne LED backlight (amber), rozszerzony zakres temperatury, RoHS
Brak towaru
Magnes trwały neodymowy walcowy o średnicy 10 mm i wysokości 4 mm.
Brak towaru
Brak towaru
Zestaw uruchomieniowy z mikrokontrolerem AT91SAM7XC256
Brak towaru
Magnes trwały neodymowy walcowy o średnicy 12 mm i wysokości 1,5 mm.
Brak towaru
Elektroniczny zestaw edukacyjny dla początkujących ROZSZERZONY o CD z kursem PKE, zasilacz płytek stykowych i zasilacz wtyczkowy 1.4A
Brak towaru
Sonda różnicowa wysokiego napięcia. Charakteryzuje się dobrymi parametrami pomiarowymi: pasmem 100 MHz oraz napięciem pracy do 750 V. Sonda ma dwa współczynniki tłumienia: 50X oraz 500X i wykorzystuje interfejs UPI. Micsig DP750-100
Brak towaru
Brak towaru
Uniwersalny moduł ze wzmacniaczem operacyjnym LM358. Zależnie do montowanych dodatkowych elementów, wzmacniacz można dowolnie konfigurować, np. jako wzmacniacz odwracający, nieodwracający, wtórnik napięciowy czy wzmacniacz całkujący. MOD-32.Z
Brak towaru
Alcohol Gas Sensor MQ-3