The Pololu USB-to-serial adapter is a tiny unit that makes it easy to connect a microcontroller project to a PC. You can connect the adapter directly to a microcontroller without an RS-232-to-TTL level converter. It is USB 2.0-compatible and will work with your existing programs that interface with a serial port.
The Pololu USB-to-serial adapter is great for connecting microcontroller projects to a personal computer. The adapter uses 3.3 V signal levels so you can connect it directly to any microcontroller running at up to 5 V without the hassle of an RS-232-to-TTL level converter. The tiny unit is only 1.0" x 0.65" including its mini-B connector, and the simple layout of the ground, transmit, and receive lines allows for easy mounting that takes up as little as four breadboard rows.
The USB adapter’s drivers make it look like a standard serial port to the operating system, allowing you to connect to all of your existing software, such as servo controller interface programs, through a USB port. The adapter is compatible with USB 2.0 standards and allows baud rates of up to 921.6 kbps. Drivers are available for Windows 98 through Vista, Linux, and Mac OSX.
With the trend toward removing serial ports from new computers, the Pololu USB-to-serial adapter provides one of the most economical, small, and simple solutions to the common problem of interfacing small projects to PCs.
Note: This product does not include printed documentation or software discs. The Pololu USB-to-serial adapter requires software drivers to operate; please see the resources tab for more information. This product requires a USB A to mini-B cable (not included) to connect to a computer.
![]() |
| Pin | Type | Function |
|---|---|---|
| DCD | In | "Data carrier detect" control input (active low) |
| DTR | Out | "Data terminal ready" control output (active low) (often used with DSR) |
| DSR | In | "Data set ready" control input (active low) (often used with DTR) |
| RTS | Out | "Ready to send" control output (often used with CTS) |
| CTS | In | "Clear to send" control input (often used with RTS) |
| GND | Power | Ground |
| TX | Out | Asynchronous serial data transmit (idle high) |
| VBUS | Power | USB bus voltage (+5V) |
| RX | In | Asynchronous serial data receive |
| SUSPEND | Out | Driven high when in USB suspend state |
| SUSPEND | Out | Driven low when in USB suspend state |
| RST | In | Device reset |
| RI | In | "Ring indicator" control input (active low) |
| VDD | Power | 3.3 V voltage regulator output |
To connect a serial device to your computer’s USB port, you will most likely only need to use the GND, TX, and RX lines. The TX and RX lines use 3.3-volt levels, but the USB adapter input lines will tolerate up to 5.5 volts. Therefore, a direct connection to a microcontroller’s I/O lines is usually possible.
For some programs, it will be necessary to connect the handshaking lines (RTS, CTS, etc.) if the software does not establish a connection without those lines. In general, the handshaking lines can be left disconnected, used for their intended purpose, or used as additional I/O lines to the computer.
![]() |
USB Cable A to Mini-B 6 ft. |
Producent BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Osoba odpowiedzialna BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Kabel z wtykami USB typ A oraz mini-USB typ B, kabel o długości 1,8 m
Brak towaru
Interfejs USB<->UART (RS232) z galwaniczną izolacją magistral z układem FT232RL
Konwerter USB-UART TTL oparty na układzie CH343G. Wyposażony w szereg zabezpieczeń zapewniających stabilną i bezpieczną komunikację. Waveshare CH343 USB UART Board (type A)
Konwerter USB-TTL ze złączami USB typu A, micro USB oraz USB typu C. Umożliwia komunikację między interfejsem szeregowym UART a interfejsem USB. SB Components 24780
Moduł WIFI-LPT100 Eval Kit umożliwia transmisję danych UART przy pomocy sieci WiFi, ultra niski pobór energii, szyfrowana komunikacja
Brak towaru
Konwerter USB - UART oparty na układzie PL2303. Kompatybilny z napięciami 1,8 V, 2,5 V, 3,3 V oraz 5 V, został wyposażony w złącze USB typu A. Waveshare PL2303 USB UART Board (type A) V2
Brak towaru
Konwerter USB - UART oparty na układzie FT232RNL. Kompatybilny z napięciami 3,3 V oraz 5 V, został wyposażony w złącze miniUSB. Waveshare FT232 USB UART Board (mini)
Konwerter USB - UART oparty na układzie PL2303. Kompatybilny z napięciami 1,8 V, 2,5 V, 3,3 V oraz 5 V, został wyposażony w złącze USB typu C. Waveshare PL2303 USB UART Board (Type C)
Kabel USB - RS-232 USB A (m) / D-Sub (m) o długości 1 m. Akyga AK-CO-02
Konwerter UART-USB oparty na układzie CP2102, moduł jest wyposażony w gniazdo mini-USB. Poziom logiczny to 3.3V lub 5V. Waveshare CP2102 USB UART Board (mini)
Moduł z konwerterem UART-RS232 przeznaczony do współpracy z Raspberry Pi Pico. Ma wbudowany układ SP3232EEN i umożliwia transmisję danych między układem z interfejsem UART a urządzeniem z RS232. Waveshare Pico-2CH-RS232
Konwerter USB - UART oparty na układzie PL2303TA. Kompatybilny z napięciami 3,3 V oraz 5 V, został wyposażony w złącze miniUSB. Waveshare PL2303 USB UART Board (mini) V2
Brak towaru
Konwerter UART-USB firmy Sparkfun oparty na układzie FT232RL, moduł wyposażony jest w gniazdo microUSB. Poziomy logiczne napięć to 3,3V lub 5V. Sparkfun BOB-12731
KAmod RS232H-mini to miniaturowy konwerter RS232 do TTL, działający w zakresie napięcia 3-5,5 V, obsługujący wszystkie sygnały RS232, z męskim złączem DB9, szpilkami goldpin 2,54 mm, bazujący na układzie MAX3243/SP3243, oferujący zabezpieczenie ESD do 15 kV i kierunek konwersji sygnałów odpowiadający urządzeniu typu DTE/Host
Moduł debuggera UART (konwerter USB-UART) zaprojektowany specjalnie dla Raspberry Pi 5. Umożliwia łatwe połączenie ze złączem debugowania UART za pomocą kabla SH1.0 3PIN, zapewniając wygodne i efektywne debugowanie. Waveshare Pi UART Debugger
Brak towaru
Kabel z wbudowanym konwerterem UART-USB, można go użyć jako interfejsu konsoli UART w Raspberry Pi oraz wielu innych komputerach jednopłytkowych, poziom logiczny linii Rx/Tx to 3.3V
Konwerter UART-USB oparty na układzie CP2102, moduł wyposażony jest w gniazdo micro-USB. Poziom logiczny to 3,3V lub 5V
Adapter USB Xbee oparty o układ FTDI. Przeznaczony do konfiguracji modułów Xbee. Dzięki żeńskiemu złączu goldpin, może być użyty jako programator FTDI dla Arduino FIO/pro/mini/lilypad. DFRobot DFR0050