![Pololu 1379 - Pololu Simple High-Power Motor Controller 24v12 Pololu 1379 - Pololu Simple High-Power Motor Controller 24v12](https://kamami.pl/8412-large_default/pololu-1379-pololu-simple-high-power-motor-controller-24v12.jpg)
![Pololu 1379 - Pololu Simple High-Power Motor Controller 24v12 Pololu 1379 - Pololu Simple High-Power Motor Controller 24v12](https://kamami.pl/8412-large_default/pololu-1379-pololu-simple-high-power-motor-controller-24v12.jpg)
562,60 zł Netto
Pololu Simple High-Power Motor Controller 24v12
darmowa wysyłka na terenie Polski dla wszystkich zamówień powyżej 500 PLN
Jeśli Twoja wpłata zostanie zaksięgowana na naszym koncie do godz. 11:00
Każdy konsument może zwrócić zakupiony towar w ciągu 14 dni bez zbędnych pytań
Pololu Simple High-Power Motor Controller 24v12
The Pololu Simple High-Power Motor Controller makes basic control of brushed DC motors easy, with our free Simple Motor Control Center software enabling quick configuration over USB. The controller supports four interface modes: USB, TTL serial, analog voltage, and hobby radio control (RC). This version operates from 5.5 to 40 V and is efficient enough to deliver a continuous 12 A without a heat sink. It ships with the power capacitor and connectors included but not soldered in, allowing for custom installations.
![]() |
Simple Motor Controllers. |
---|
The Pololu Simple Motor Controllers are versatile, general-purpose motor controllers for brushed, DC motors. A wide operating range of up to 5.5–40V and the ability to deliver up to several hundred Watts in a small form factor make these controllers suitable for many motor control applications. With a variety of supported interfaces—USB for direct connection to a computer, TTL serial for use with embedded systems, RC hobby servo pulses for use as an RC-controlled electronic speed control (ESC), and analog voltages for use with a potentiometer or analog joystick—and a wide array of configurable settings, these motor controllers make it easy to add basic control of brushed DC motors to a variety of projects. Although this motor controller has many more features than competing products, a free configuration utility (for Windows 7, Vista, Windows XP, and Linux) simplifies initial setup of the device and allows for in-system testing and monitoring of the controller via USB.
For 24 V applications, we recommend the 24v12 or 24v23 versions. We strongly recommend against using the 18v7, 18v15, or 18v25 with 24 V batteries, which can significantly exceed 24 V when fully charged and are dangerously close to the maximum voltage limits of these lower-voltage controllers.
![]() |
Simple High-Power Motor Controller 18v25 or 24v23 simplified connection diagram. |
---|
|
|
Note: A USB A to mini-B cable (not included) is required to connect this controller to a computer.
![]() |
Two Pololu Simple Motor Controllers enable mixed RC-control of Dagu Wild Thumper 4WD all-terrain chassis. |
---|
The Simple Motor Controllers are available in several input voltage ranges and output current ranges:
![]() 18v7 | ![]() 18v15 | ![]() 24v12 | ![]() 18v25 | ![]() 24v23 | |
---|---|---|---|---|---|
Absolute max voltage: | 30 V | 30 V | 40 V | 30 V | 40 V |
Recommended max voltage(1): | 24 V | 24 V | 34 V | 24 V | 34 V |
Max continuous current w/o heat sink: | 7 A | 15 A | 12 A | 25 A | 23 A |
Width: | 1.1" (2.8 cm) | 1.1" (2.8 cm) | 1.1" (2.8 cm) | 1.2" (3.1 cm) | 1.2" (3.1 cm) |
Length: | 2.1" (5.3 cm) | 2.1" (5.3 cm) | 2.1" (5.3 cm) | 2.3" (5.8 cm) | 2.3" (5.8 cm) |
Weight(2): | 7 g | 7 g | 7 g | 12 g | 12 g |
Available with connectors installed? | Yes | Yes | Yes | No | No |
1 We do not recommend using the 18v7, 18v15, or 18v25 versions with 24 V batteries, which can significantly exceed 24 V when fully charged. The 24v12 and 24v23 are the much more appropriate controller for 24 V applications.
2 This is the weight of the board without header pins, terminal blocks, or through-hole power capacitor.
|
|
Most Simple Motor Controllers are available “fully assembled”, with the power capacitor and connectors pre-installed, or with these components included but not soldered in. For example, a fully assembled 18v15 ships as shown in the left picture above, and an 18v15 with included hardware ships as shown in the right picture above (the included hardware consists of a power capacitor, a 40×1 straight 0.1" male header strip, a 5mm-pitch 4-pin terminal block, and a blue shorting block).
The connector-free version allows flexibility in choice of connectors and placement of the power capacitor (e.g. on the other side of the board) to accommodate compact installations or to make room for a heat sink.
Note: The power capacitor has a significant effect on performance; the included capacitor is the minimum size recommended, and bigger ones can be added if there is space. A bigger capacitor might be required if the power supply is poor or far (more than about a foot) from the controller.
The included terminal blocks are only rated for 16 A, so we recommend soldering thick wires directly to the connector-free version of the board and using higher-current connectors for applications that will exceed the terminal blocks’ ratings.
|
|
|
Warning: Take proper safety precautions when using high-power electronics. Make sure you know what you are doing when using high voltages or currents! During normal operation, this product can get hot enough to burn you. Take care when handling this product or other components connected to it.
Sterownik silnika krokowego z uładem DRV8825, pozwala na zasilanie silnika bipolarnego prądem do 1,5A na fazę. Możliwośc kontroli za pomocą interfejsów: I2C, szeregowego TTL, USB, a także potencjometru, enkodera lub STEP/DIR. Pololu 3131
Moduł sterownika dwóch silników szczotkowych DC o wydajności prądowej do 5 A na kanał. Może współpracować z pakietami LiPo 2S i 3S
Brak towaru
Jednokanałowy sterownik silników DC z interfejsem I2C. Jest zasilany napięciem od 1,8 V do 22 V i może dostarczyć prąd o natężeniu do 1,8 A. Płytka z przylutowanymi złączami. Pololu 5074
Rozszerzenie dla Raspberry Pi z dwoma sterownikami silników obsługującymi zakres napięć 5-28 V i prąd ciągły 3 A (chwilowy 5 A) każdy. Pololu 2755
Pololu G2 24v12 High Power to miniaturowy sterownik silnika DC. Zasilanie sterownika: 6,5...30V. Wydajność prądowa modułu: 12A. Moduł posiada zabezpieczenie przed napięciem wstecznym i przepięciami. Pololu 1364
DRV8825 Stepper Motor Driver Carrier to sterownik silnika krokowego z układem A4988, pozwala na zasilanie silnika bipolarnego prądem do 1,2 A na fazę, bez użycia radiatora. Układ może być zasilany napięciem do 35 V. Pololu 2980
Brak towaru
Pololu G2 24v19 High Power to miniaturowy sterownik silnika DC. Zasilanie sterownika: 6,5...40V. Wydajność prądowa modułu: 19A. Moduł posiada zabezpieczenie przed napięciem wstecznym i przepięciami. Pololu 1367
Brak towaru
Niewielkich rozmiarów moduł sterownika silnika krokowego TB67S249FTG zasilanego napięciem 10...47V i prądzie pracy 1,6A. Sterownik pozwala na kontrolowanie ruchu silnika aż z 7 różnymi rozdzielczościami (do 1/32 kroku). Pololu 3096
Pololu Jrk 21v3 USB Motor Controller with Feedback (Fully Assembled)
Moduł rozszerzeń przeznaczony do współpracy z micro:bit. Pozwala na sterownie 4 silnikami DC lub dwoma silnikami krokowymi i 8 serwami. Komunikuje się przez interfejs I2C. DFRobot DFR0548
Sterownik silników krokowych, który może pracować z napięciem z zakresu od 24 do 110 VDC lub od 18 do 80 VAC oraz maksymalnym prądem do 8,4 A. Umożliwia konfigurację mikro kroku w zakresie od 2 do 256. 2DM860H
Niewielkich rozmiarów moduł sterownika silnika krokowego TB67S279FTG zasilanego napięciem 10...47V i prądzie pracy 1,1A. Sterownik pozwala na kontrolowanie ruchu silnika aż z 7 różnymi rozdzielczościami (do 1/32 kroku). Pololu 3098
Kompaktowy sterownik silnika krokowego z układem TMC2225 o napięciu pracy od 4,75 do 36 V. Oferuje płynną, cichą pracę, wysoką wydajność, różnorodne tryby pracy oraz łatwą konfigurację. Jest sterowany przez interfejs STEP/DIR i stanowi idealne rozwiązanie dla drukarek 3D oraz podobnych zastosowań. BIGTREETECH TMC2225 V1.0
Brak towaru
Sterownik silników DC, który pozwala na kontrolowanie ruchu dwóch napędów za pomocą interfejsu I2C. Płytka z przylutowanymi złączami. Pololu 5042
Brak towaru
Sterownik silników DC, który pozwala na kontrolowanie ruchu dwóch napędów za pomocą interfejsu I2C. Płytka ze złączami do montażu. Pololu 5049
Brak towaru
Sterownik silnika krokowego z uładem DRV8825, pozwala na zasilanie silnika bipolarnego prądem do 1,5A na fazę. Możliwośc kontroli za pomocą interfejsów: I2C, szeregowego TTL, USB, a także potencjometru, enkodera lub STEP/DIR. Wersja z przylutowanymi złączami. Pololu 3130
Brak towaru
Pololu Simple High-Power Motor Controller 24v12