

zł562.60 tax excl.
Pololu Simple High-Power Motor Controller 24v12
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
Pololu Simple High-Power Motor Controller 24v12
The Pololu Simple High-Power Motor Controller makes basic control of brushed DC motors easy, with our free Simple Motor Control Center software enabling quick configuration over USB. The controller supports four interface modes: USB, TTL serial, analog voltage, and hobby radio control (RC). This version operates from 5.5 to 40 V and is efficient enough to deliver a continuous 12 A without a heat sink. It ships with the power capacitor and connectors included but not soldered in, allowing for custom installations.
![]() |
Simple Motor Controllers. |
---|
The Pololu Simple Motor Controllers are versatile, general-purpose motor controllers for brushed, DC motors. A wide operating range of up to 5.5–40V and the ability to deliver up to several hundred Watts in a small form factor make these controllers suitable for many motor control applications. With a variety of supported interfaces—USB for direct connection to a computer, TTL serial for use with embedded systems, RC hobby servo pulses for use as an RC-controlled electronic speed control (ESC), and analog voltages for use with a potentiometer or analog joystick—and a wide array of configurable settings, these motor controllers make it easy to add basic control of brushed DC motors to a variety of projects. Although this motor controller has many more features than competing products, a free configuration utility (for Windows 7, Vista, Windows XP, and Linux) simplifies initial setup of the device and allows for in-system testing and monitoring of the controller via USB.
For 24 V applications, we recommend the 24v12 or 24v23 versions. We strongly recommend against using the 18v7, 18v15, or 18v25 with 24 V batteries, which can significantly exceed 24 V when fully charged and are dangerously close to the maximum voltage limits of these lower-voltage controllers.
![]() |
Simple High-Power Motor Controller 18v25 or 24v23 simplified connection diagram. |
---|
|
|
Note: A USB A to mini-B cable (not included) is required to connect this controller to a computer.
![]() |
Two Pololu Simple Motor Controllers enable mixed RC-control of Dagu Wild Thumper 4WD all-terrain chassis. |
---|
The Simple Motor Controllers are available in several input voltage ranges and output current ranges:
![]() 18v7 | ![]() 18v15 | ![]() 24v12 | ![]() 18v25 | ![]() 24v23 | |
---|---|---|---|---|---|
Absolute max voltage: | 30 V | 30 V | 40 V | 30 V | 40 V |
Recommended max voltage(1): | 24 V | 24 V | 34 V | 24 V | 34 V |
Max continuous current w/o heat sink: | 7 A | 15 A | 12 A | 25 A | 23 A |
Width: | 1.1" (2.8 cm) | 1.1" (2.8 cm) | 1.1" (2.8 cm) | 1.2" (3.1 cm) | 1.2" (3.1 cm) |
Length: | 2.1" (5.3 cm) | 2.1" (5.3 cm) | 2.1" (5.3 cm) | 2.3" (5.8 cm) | 2.3" (5.8 cm) |
Weight(2): | 7 g | 7 g | 7 g | 12 g | 12 g |
Available with connectors installed? | Yes | Yes | Yes | No | No |
1 We do not recommend using the 18v7, 18v15, or 18v25 versions with 24 V batteries, which can significantly exceed 24 V when fully charged. The 24v12 and 24v23 are the much more appropriate controller for 24 V applications.
2 This is the weight of the board without header pins, terminal blocks, or through-hole power capacitor.
|
|
Most Simple Motor Controllers are available “fully assembled”, with the power capacitor and connectors pre-installed, or with these components included but not soldered in. For example, a fully assembled 18v15 ships as shown in the left picture above, and an 18v15 with included hardware ships as shown in the right picture above (the included hardware consists of a power capacitor, a 40×1 straight 0.1" male header strip, a 5mm-pitch 4-pin terminal block, and a blue shorting block).
The connector-free version allows flexibility in choice of connectors and placement of the power capacitor (e.g. on the other side of the board) to accommodate compact installations or to make room for a heat sink.
Note: The power capacitor has a significant effect on performance; the included capacitor is the minimum size recommended, and bigger ones can be added if there is space. A bigger capacitor might be required if the power supply is poor or far (more than about a foot) from the controller.
The included terminal blocks are only rated for 16 A, so we recommend soldering thick wires directly to the connector-free version of the board and using higher-current connectors for applications that will exceed the terminal blocks’ ratings.
|
|
|
Warning: Take proper safety precautions when using high-power electronics. Make sure you know what you are doing when using high voltages or currents! During normal operation, this product can get hot enough to burn you. Take care when handling this product or other components connected to it.
Data sheet
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Black Edition offers adjustable current limiting, over-current and over-temperature protection, and five different microstep resolutions. It operates from 8 V to 35 V and can deliver up to 2 A per coil with sufficient additional cooling. Pololu 2128
The RoboClaw Solo motor controllers from Basicmicro (formerly Ion Motion Control) can control a single brushed DC motor using USB serial, TTL serial, RC, or analog inputs. An integrated quadrature decoder make it easy to create a closed-loop speed control system.
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1363
Module with a 2-channel driver for DC motors TB6612FNG designed to work with the Raspberry Pi. It can work with voltages from 6 to 12 V and currents up to 3 A. SB Components 21468
Two-channel ESC controller for brushed motors. It can deliver 40 A and has wires terminated with an XT60 connector
No product available!
Pololu Simple High-Power Motor Controller 18v15
No product available!
Module with the driver of motors TB6612FNG and driver PWM PCA9685 for Raspberry Pi Pico. It allows you to control the movement of 4 DC motors. Waveshare Pico-Motor-Driver
Pololu Low-Voltage Dual Serial Motor Controller
DC motor driver with voltage 4.5..28V and maximum continuous current of 2.6A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3143
No product available!
Motor-driven expansion board for Arduino, L293D, 74HC595 shift register, RoHS
TB6612FNG Dual Motor Driver Carrier
Compact stepper motor controller with the TMC5160 system with operating voltage from 8 to 35 V. It offers smooth, quiet operation, high efficiency, various operating modes and easy configuration. It is controlled via the SPI interface and is an ideal solution for 3D printers and similar applications. BIGTREETECH TMC5160 V1.3
No product available!
The module with the DRV8830 DC motor controller with a maximum current of 1 A. The board is equipped with a screw connector and communicates via the I2C interface. Pimoroni PIM479
ESC controller module for a brushless motor with a current capacity of up to 120 A. It can work with LiPo packs from 5S to 12S. Uses BLHeli_32 software. FLYCOLOR X-CROSS HV
DC motor driver with voltage 6.5..40V and maximum continuous current 21A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3149
DC motor driver that allows you to control the movement of three drives using the I2C interface. Board with soldered connectors. Pololu 5033
Pololu Simple High-Power Motor Controller 24v12