- Obecnie brak na stanie
Generic Linear Actuator: 4" Stroke, 12V, 1.5"/s
This 12 V linear actuator has a load rating of 22 lbs (10 kg) and a maximum speed of 1.5 in/s (40 mm/s). Limit switches at each end make the actuator easy to control over its full range of motion, and the worm drive ensures that the shaft will hold its position even when unpowered. This version has a 4-inch stroke and no potentiometer.
These low-cost linear actuators are 12V DC gearmotors that use a worm drive to move a shaft back and forth along its length. The worm drive ensures that the shaft will hold its position even when unpowered. Two limit switches safely stop the motor at either end of its range, while diodes allow it to reverse direction after reaching a limit point. The actuators are mostly metal, and the entire case is sealed to protect against dust and water (rated IP54).
![]() |
| Generic linear actuator with 8? stroke, fully extended. |
|---|
The linear actuators are available in a variety of lengths and with optional potentiometers that are linked to the shaft position, for use in feedback systems. They are also available in two speeds: 0.6?/s (16 mm/s) and 1.5?/s (40 mm/s). The slower 0.6?/s versions can exert a maximum force of about 110 lbs (500 N or 51 kg), while the faster 1.5?/s versions can exert up to 22 lbs (100 N or 10 kg).
You can use the table on our linear actuator category page to help you find the actuator with the combination of speed and force that best meets your project’s requirements.
Mounting brackets are available for attaching the actuators to a structure; two are required for each actuator.
![]() |
| Bracket connected to one end of a generic linear actuator. |
|---|
To test-drive the actuator, simply connect a power source of up to 12 V to the motor leads. Reversing the applied voltage will reverse the direction of motion. A motor controller or motor driver is required for electronic speed and direction control. We recommend our Jrk Motor Controllers for use with the feedback actuators and the Pololu Simple Motor Controller 18v7 for controlling the actuators without feedback, though many of our other motor controllers and motor drivers are capable of powering this actuator.
These actuators have a stall current of 7 A at 12 V, but they will, on average, draw far less than this when used within their load ratings. They draw around 1 A with no load and approximately 3 A at their maximum rated load, so we have found they generally work well with our lower-power jrk 21v3 motor controller with feedback (see the bottom of this page for more information using this controller for closed-loop linear actuator position control). Note, however, that the actuators can briefly draw close to their full stall current when abruptly started or on a sudden change of direction. Such current spikes can be dampened if you take steps to limit the acceleration of the actuator (many of our motor controllers offer optional acceleration limiting).
Diagrams of the linear actuators are shown below. Please note that the actuator stroke lengths in inches are nominal; the actual dimensions are specified in millimeters. The versions that include potentiometers have a larger gearbox, so their overall size and weight is larger.
![]() |
| Dimensions (in mm) of the generic linear actuators without feedback. |
|---|
![]() |
| Dimensions (in mm) of the generic linear actuators with feedback. |
|---|
| Stroke length | Without feedback | With feedback | ||
|---|---|---|---|---|
| Retracted length | Extended length | Retracted length | Extended length | |
| 100 mm (~4?) | 205 mm | 305 mm | 240 mm | 340 mm |
| 200 mm (~8?) | 305 mm | 505 mm | 340 mm | 540 mm |
| 300 mm (~12?) | 405 mm | 705 mm | 440 mm | 740 mm |
Each actuator has a 3-foot-long cable. Actuators without feedback have two unterminated, stripped power leads as shown in the left picture below. On actuators with feedback, the cable includes three additional potentiometer leads as shown in the right picture below. The potentiometer has an end-to-end resistance of 10 kΩ; the yellow and white leads are connected to its end terminals, while the blue lead is connected to its wiper. The resistance between the blue and white leads increases as the actuator extends.
|
|
The feedback feature included with our jrk motor controllers make them a great solution for precisely controlling our linear actuators with feedback. Our settings file for the jrk configuration utility makes setup easy, eliminating the need to calibrate the feedback and tune the PID constants. To get started, follow the steps below:
![]() |
| Connecting a LACTxP linear actuator with feedback to a jrk 21v3 motor controller. |
|---|
While this setting file gives precise control over most of an actuator’s range, you might find decreased performance very near the extremes due to the limit switches. The voltage range covered by the potentiometer also varies among different actuators. If your project requires better control, you might need to recalibrate the feedback settings for your particular actuator.
Producent
Osoba odpowiedzialna
Oficjalny przewód HDMI 2.0 do Raspberry Pi o długości 1m w kolorze czarnym. Kompatybilny z Raspberry Pi 3 oraz poprzednimi wersjami.
Brak towaru
Żarówka LED RGB sterowana za pomocą WiFi. Posiada popularną oprawę E27. Umożliwia zdalne sterowanie kolorem, jasnością i temperaturą barwy za pomocą aplikacji EWeLink. Sonoff B1
Brak towaru
Zestaw z taśmą LED (o długości 2 metrów) sterowaną za pomocą WiFi. Jest odporna na wodę (standard ochrony IP65). Sterowana za pomocą aplikacji EWeLink. Sonoff L1 Smart Led light Strip
Brak towaru
Klawiatura USB w kolorze czarnym, ze standardowymi klawiszami funkcyjnymi. Klawiatura współpracuje z Raspberry Pi, Odroid i innymi komputerami. Titanum TK101
Brak towaru
Oficjalny zasilacz do Raspberry Pi o napięciu wyjściowym 5,1V oraz wydajności prądowej 2,5A. Zasilacz w kolorze białym. T6090DV
Brak towaru
Oficjalny zasilacz do Raspberry Pi o napięciu wyjściowym 5,1V oraz wydajności prądowej 2,5A. Zasilacz w kolorze czarnym. T6090DV
Brak towaru
Moduł LOGO! 12/24RCEO z interfejsem Ethernet i serwerem WEB. Posiada pamięć o rozmiarze 400 bloków oraz funkcję logowania danych na karcie microSD, nie posiada wyświetlacza. Siemens 6ED1052-2MD08-0BA0
Brak towaru
Regulowany, izolowany kontroler zasilania prądu stałego z wewnętrznym sterownikiem MOSFET z wbudowanym sprzężeniem zwrotnym. Analog Devices ADUM4070ARIZ
Brak towaru
1-kanałowy dotykowy włącznik światła z łącznością WiFi. Pozwala użytkownikom na zdalne włączanie/wyłączanie podłączonych diod LED i światłem z dowolnego miejsca w dowolnym czasie oraz ustawić harmonogramy czasowe za pomocą aplikacji eWeLink. Sonoff Touch
Brak towaru
Zestaw wentylatora z radiatorem do minikomputera NVIDIA Jetson TX1/TX2. DCV-01672-N2-GP
Brak towaru
Radiator przeznaczony dla modułów NVIDIA Jetson TX1 i TX2 o wymiarach 87 x 57 x 16 mm. Pozwala na efektywne chłodzenie procesora, przy zachowaniu ciszy. XHG301
Brak towaru
Płyta bazowa do modułów NVIDIA Jetson TX1, Jetson TX2 lub Jetson TX2i . Wyposażona w 5 portów Gigabit Ethernet, HDMI Video, USB 3.0, USB 2.0, USB OTG, Mini-PCIe/mSATA oraz dwa porty szeregowe RS-232. Connect Tech ASG007
Brak towaru
Płyta bazowa do modułów NVIDIA Jetson TX2/TX2i i Jetson TX1. Wyposażona w 2 porty Gigabit Ethernet, HDMI, USB 3.0, USB 2.0, USB CLIENT, a także rozszerzenie miniPCIe, mSATA ora opcjonalny moduł GPS/GNSS. Connect Tech ASG006/ASG009
Brak towaru
Płyta bazowa do modułów NVIDIA Jetson TX2/TX2i i Jetson TX1. Wyposażona MIPI CSI-2, rozszerzenie Mini-PCIe/mSATA, HDMI Video, USB 3.0 i 2.0 oraz dwa porty szeregowe dla RS-232/485. Connect Tech ASG002
Brak towaru
Moduł przełącznika opartego o przekaźnik z funkcją sterowania za pomocą sieci WiFi. Może zostać podłączony do sieci WiFi lub działać jako samodzielny punkt dostępu. Shelly 1 Open Source
Brak towaru
Moduł przełącznika opartego o przekaźnik z funkcją sterowania za pomocą sieci WiFi. Może zostać podłączony do sieci WiFi lub działać jako samodzielny punkt dostępu. Posiada funkcję pomiaru zużycia energii elektrycznej oraz zabezpieczenie przez przeciążeniem/przegrzaniem. Shelly 1PM
Brak towaru
Generic Linear Actuator: 4" Stroke, 12V, 1.5"/s