- Obecnie brak na stanie
Carbon Monoxide Gas Sensor MQ-7
This semiconductor gas sensor detects the presence of Carbon Monoxide at concentrations from 10 to 10,000 ppm. The sensor’s simple analog voltage interface requires only one analog input pin from your microcontroller.
![]() |
This Carbon Monoxide (CO) gas sensor detects the concentrations of CO in the air and ouputs its reading as an analog voltage. The sensor can measure concentrations of 10 to 10,000 ppm.The sensor can operate at temperatures from -10 to 50°C and consumes less than 150 mA at 5 V. Please read the MQ7 datasheet (185k pdf) for more information about the sensor.
![]() |
| Gas sensor with orange plastic case bottom view. |
|---|
Connecting five volts across the heating (H) pins keeps the sensor hot enough to function correctly. Connecting five volts at either the A or B pins causes the sensor to emit an analog voltage on the other pins. A resistive load between the output pins and ground sets the sensitivity of the detector. The resistive load should be calibrated for your particular application using the equations in the datasheet, but a good starting value for the resistor is 10 kΩ.
We offer two breakout boards that make it easier to interface with these sensors: a Pololu carrier board and a SparkFun carrier board. The Pololu version is shown below.
|
![]() |
Pololu MQ Gas Sensor Carrier |
![]() |
Flammable Gas & Smoke Sensor MQ-2 |
![]() |
Alcohol Gas Sensor MQ-3 |
Producent BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Osoba odpowiedzialna BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Brak towaru
Izolowana sonda światłowodowa o zakresie pomiarowym do 1000 V. Pracuje w paśmie do 1 GHz, może być podłączona do oscyloskopu przez złącze BNC. Zasilana bateryjnie. Micsig OIP1000B
Brak towaru
HumidIcon™ Digital Humidity/Temperature Sensor, I2C, hydrophobic filter, SOIC8, Honeywell, RoHS
Brak towaru
Brak towaru
Brak towaru
Zestaw podstawowych elementów elektronicznych w komplecie z płytką stykową, przewodami połączeniowymi oraz płytką Arduino UNO R3. Idealnie nadaje się dla początkujących elektroników poznających również Arduino. ArduCAM KB0001
Brak towaru
Płytka drukowana do praktycznego zasilacza warsztatowego. AVT3172 A
Brak towaru
Zestaw AVT do samodzielnego montażu 8-kanałowego przełącznika sterowanego dowolnym pilotem na podczerwień. AVT3138 B
Brak towaru
Przetwornik napięcia stałego na szerokość impulsu - zestaw do samodzielnego montażu
Brak towaru
Brak towaru
Brak towaru
GD32E230C8T6, Mikrokontroler ARM Cortex-M23; SRAM: 8kb; Flash: 64kb; 72MHz; LQFP48
Brak towaru
Prototypowa płytka stykowa 170 punktów o wymiarach 35x47 mm w kolorze czerwonym. Pololu 1491
Brak towaru
Brak towaru
Alicja Żarowska-Mazur, Dawid Mazur
SUPERLUMISCENCYJNY MODUŁOWY OŚWIETLACZ 3x3LED ZIELONE 20mA - ZESTAW DO SAMODZIELNEGO MONTAŻU
Brak towaru
Carbon Monoxide Gas Sensor MQ-7