- Out-of-Stock
zł10,639.61
.png)
New products
New products New products
Pololu 1482 - Carbon Monoxide Gas Sensor MQ-7
ID: 196146
Carbon Monoxide Gas Sensor MQ-7
Carbon Monoxide Gas Sensor MQ-7
This semiconductor gas sensor detects the presence of Carbon Monoxide at concentrations from 10 to 10,000 ppm. The sensor’s simple analog voltage interface requires only one analog input pin from your microcontroller.
 |
Overview
This Carbon Monoxide (CO) gas sensor detects the concentrations of CO in the air and ouputs its reading as an analog voltage. The sensor can measure concentrations of 10 to 10,000 ppm.The sensor can operate at temperatures from -10 to 50°C and consumes less than 150 mA at 5 V. Please read the MQ7 datasheet (185k pdf) for more information about the sensor.
 |
| Gas sensor with orange plastic case bottom view. |
|---|
Connections
Connecting five volts across the heating (H) pins keeps the sensor hot enough to function correctly. Connecting five volts at either the A or B pins causes the sensor to emit an analog voltage on the other pins. A resistive load between the output pins and ground sets the sensitivity of the detector. The resistive load should be calibrated for your particular application using the equations in the datasheet, but a good starting value for the resistor is 10 kΩ.
We offer two breakout boards that make it easier to interface with these sensors: a Pololu carrier board and a SparkFun carrier board. The Pololu version is shown below.
|
People often buy this product together with:
 |
Pololu MQ Gas Sensor Carrier |
 |
Flammable Gas & Smoke Sensor MQ-2 |
 |
Alcohol Gas Sensor MQ-3 |
196146
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Other products in the same category (16)
Evaluation Board for Freescale Xtrinsic Sensors - Sensors, Altitude & Pressure Measurement, Magnetic Field & Physical Position Detection
For use with Freescale FRDM-KL25z and Raspbery Pi Host Platforms
Delivery date unknown
No product available!
Pin header goldpin black 1x3 pins. Straight connector for through-hole assembly. 2.54mm pitch
Retired
No product available!
No product available!
Joshua J. Drake, Zach Lanier, Collin Mulliner, Pau Oliva Fora, Stephen A. Ridley, Georg Wicherski
Retired
No product available!
Tomasz Frenchman
Retired
No product available!
No product available!
No product available!
No product available!
A functional expander for NUCLEO and Arduino with a set of environmental sensors: pressure, humidity, temperature and light intensity and also a 5-position joystick and LED RGB.
Retired
No product available!
No product available!
Starter kit with the Altera FPGA system from the MAX10 family, which in addition to the classic, configurable logical resources are equipped with a 12-bit ADC converter, Flash memory for the user and internal configuration memory. The set is equipped with Arduino system connectors and basic peripherals for project testing.
Delivery date unknown
No product available!
Magnetic Displacement Sensors, SOIC8, Honeywell Microelectronics & Precision Sensors, RoHS
Retired
No product available!
Miniature (22x13.5x6mm) WiFi module b / g / n with TCP and UDP protocols operating in standalone and access point modes. 2.0mm goldpin connector. The module is equipped with a UART interface, it is also possible to control GPIO lines (also as PWM). Powered by 3.3V. I-PEX connector
Delivery date unknown
No product available!
No product available!
No product available!
Quadia® Tegra® K1 SOC four-core computer supporting CUDA®, RoHS technology
Retired
No product available!
Carbon Monoxide Gas Sensor MQ-7