- Obecnie brak na stanie
 
        
          ADMP401 MEMS Microphone Breakout Board
Ready to add sound detection to your next project? This small breakout board from SparkFun couples a tiny microelectromechanical system (MEMS) microphone with a 67x gain external amplifying circuit, converting sound into analog voltage signals that can be measured by a microcontroller’s analog-to-digital converter (ADC). The unit comes fully assembled as shown and works from 1.5 to 3.3 V.
This tiny microphone board from SparkFun is a carrier for Analog Device’s ADMP401 Omnidirectional Microphone with Bottom Port and Analog Output. Therefore, careful reading of the the ADMP401 datasheet (179k pdf) is recommended. The board includes an amplifying circuit with a gain of 67 that matches the bandwidth requirements of the ADMP401. The amplifier’s AUD output will float at one half Vcc when no sound is being picked up, and the amplifier produces a peak-to-peak output of about 200mV when the microphone is held at arms length and is being talked into at normal conversational volume levels. The convenient output voltage range of AUD means it can be directly connected to the ADC of a typical microcontroller.
The ADMP401 is a bottom port microphone, which allows the microphone to be mounted flush against the outside wall of an enclosure. The breakout board pins have a 0.1" pitch, making the board compatible with standard 0.1" protoboards, breadboards, 0.1" male headers, and 0.1" female headers.
|  | Electret Microphone Breakout Board | 
|  | Pololu Carrier with Sharp GP2Y0D810Z0F Digital Distance Sensor 10cm | 
|  | 16mm Speaker: 16 Ohm, 0.5 W | 
Producent BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Osoba odpowiedzialna BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Moduł z mikrofonem MEMS; model SPW2430 z wbudowanym wzmacniaczem. Na płytce znalazł się także stabilizator napięcia 3,3 V potrzebnego do zasilenia mikrofonu. Adafruit 2716
 Brak towaru
Zestaw Pi Desktop pozwala przekształcić Raspberry Pi w pełnoprawny system desktopowy. Dołączona nakładka na piny GPIO zawiera zegar RTC i układ zarządzania energią. Pozwala też na dołączenie dysku mSATA oraz modułu kamery. Pi Desktop
 Brak towaru
"Digital Design using Digilent FPGA Boards 2nd Edition, 2012" Richard E. Haskell & Darrin M. Hanna -- EDU
 Brak towaru
 Brak towaru
 Brak towaru
 Brak towaru
 Brak towaru
Filament firmy ROSA3D wykonany z wysokiej jakości granulatu PLA. Na szpuli nawinięte jest 0,8 kg filamentu o średnicy 1,75 mm. ROSA3D PLA Multicolor Silk Jungle
 Brak towaru
Sonda różnicowa Micsig z serii DP oparta na zaawansowanej technologii SigOFIT. Oferuje pasmo częstotliwości 150 MHz oraz możliwość pomiarów napięcia do 700 V. Wykorzystuje popularne złącze BNC i jest zasilana przez złącze USB typu C. Micsig DP701
 Brak towaru
 Brak towaru
Automat Kolarz od UGEARS to nie tylko model, to prawdziwa przygoda konstruowania i odkrywania, która zakończy się osobistym triumfem, gdy kolarz ruszy do wyścigu na Twoim biurku. UGears 70148
 Brak towaru
 Brak towaru
Złącze listwowe goldpin czarne 1x3 szpilki. Złącze proste do montażu przewlekanego. Raster 2.54mm
 Brak towaru
PCB i zaprogramowany układ do miniaturowego sterownika taśmy LED. AVT1847 A+
 Brak towaru
 Brak towaru
Thermopad, taśma termoprzewodząca dwustronnie przylepna 20mm x 130mm x 3mm, 6W/mK, AG Termopasty, RoHS
 Brak towaru
 
                    ADMP401 MEMS Microphone Breakout Board