- Obecnie brak na stanie

DEV-09595 - MIDI Shield
Description: The MIDI Shield board gives your Arduino access to the antiquated, but still widely used and well supported MIDI communication protocol, so you can control synthesizers, sequencers, and other musical devices. The MIDI protocol shares many similarities with standard asynchronous serial interfaces, so you can use the UART pins of your Arduino to send and receive MIDI's event messages.
The MIDI Shield provides an opto-isolated MIDI-IN port as well as a MIDI-OUT port. The MIDI Shield can be mounted directly on top of an Arduino, connecting the MIDI-IN to the Arduino's hardware RX pin and the MIDI-OUT to TX. Potentiometers are connected to analog pins 1 and 2, and can be used to control volume, pitch, tone or anything else you'd like. Also connected on the shield are three momentary push buttons (connected to D2-4), a reset button, and green and red stat LEDs. The RUN/PROG switch allows you to program the Arduino over serial without having to remove the shield.
Note: The MIDI Shield does not come with the through-hole MIDI connectors or trimpots soldered on. All of these components (2 MIDI connectors and 2 trimpots) are included with the product, however
Note: When using this shield with the Arduino Pro you will have to bypass the TX/RX resistors on the Pro to get enough current to the shield.
Documents:
Producent BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Osoba odpowiedzialna BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Moduł LTE Cat 4, który obsługuje komunikację bezprzewodową w ramach technologii LTE-TDD, LTE-FDD, HSPA+, GSM, GPRS i EDGE. W zestawie z anteną SMA. Waveshare SIM7600E-H 4G Module (B)
Brak towaru
Zestaw startowy firmy Freescale z mikrokontrolerem z rodziny Kinetis KL25Z (Cortex-M0+), zintegrowany z programatorem-debuggerem OpenSDA, nastawnikiem pojemnościowym, LED-RGB, akcelerometrem MEMS 3D i shieldem z sensorami MEMS: MPL3115 , MAG3110, MMA8491Q. Wyprowadzenia zgodne z Arduino.
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Płyta bazowa do modułów Trenz Electronics 4 x 5 cm, np do TE0741. Płyta umożliwia podłączenie do modułu interfejsów: USB, Ethernet, JTAG, UART. TE0703-05
Brak towaru
Zestaw AVT do samodzielnego montażu uniwersalnego modułu zasilającego 9V. AVT1895/9 B
Brak towaru
Laserowy czujnik odległości o zakresie pomiarowym do 2 m bazujący na technice pomiaru ToF. Komunikacja z modułem odbywa się przez interfejs I2C. Waveshare VL53L0X Distance Sensor
Brak towaru
COM-12656 - EasyVR Shield 2.0 - Voice Recognition Shield, RoHS
Brak towaru
Miernik grubości lakieru GL-2B Fe&Al umożliwia pomiar lakierowanych blach stalowych, stalowych ocynkowanych oraz aluminiowych. Urządzenie ma pamięć 100 pomiarów. W zestawie płytki do kalibracji. Wyświetlacz jest podświetlany
Brak towaru
Brak towaru
Brak towaru
Ręczna kamera termowizyjna z wyświetlaczem LCD o przekątnej 3,2". Wykonuje pomiar temperatury w zakresie od -20 do 300°C z dokładnościa do 2°C. HTI HT-19
Brak towaru
Filament firmy ROSA3D wykonany z wysokiej jakości granulatu PLA. Na szpuli nawinięte jest 0,5 kg filamentu o średnicy 1,75 mm. Świeci w ciemności na kolor zielony. ROSA3D PLA Starter Glow in the Dark Green
Brak towaru
Brak towaru
DEV-09595 - MIDI Shield