- Obecnie brak na stanie
![KIT-13199 KIT-13199](https://kamami.pl/19428-large_default/sparkfun-gps-shield-kit.jpg)
KIT-13199
darmowa wysyłka na terenie Polski dla wszystkich zamówień powyżej 500 PLN
Jeśli Twoja wpłata zostanie zaksięgowana na naszym koncie do godz. 11:00
Każdy konsument może zwrócić zakupiony towar w ciągu 14 dni bez zbędnych pytań
KIT-13199 SparkFun GPS Shield Kit
Description:
This is the SparkFun GPS Shield Kit, a great launch pad for anyone looking to get into the world of GPS. This little kit includes our GPS Shield, an EM-506 GPS Receiver with interface cable, and a set of R3 headers to solder onto the shield. Adding GPS to your Arduino has never been easier. Multiple GPS receivers attach easily to the shield, and with the example sketch (check below), you will be able to locate your exact position within a few meters. Here’s where we are. GPS also gives you amazingly accurate time!
A connector for the popular EM-506 GPS receiver is populated on the board, and footprints for EM-408 and EB-85A connectors are also made available (connectors are not included and can be found below in the related items). The regular GPS pins (RX, TX, PPS, etc.) are also broken out to a 10-pin 0.1" pitch header, and a small prototyping area is also provided.
The DLINE/UART switch switches the GPS module’s input/output between Arduino’s standard TX/RX pins or any digital pins on the Arduino (default setting uses pins 3 and 2 connected to TX and RX, respectively). The DLINE/UART switch must be set to DLINE in order to upload code through the Arduino IDE.
The shield also includes the footprint for a 12 mm coin cell battery holder to provide battery backup to the optional EB-85A GPS module.An ON/OFF switch is included which controls power to the GPS module. Additionally, the Arduino reset switch is also brought out.
Includes:
Features:
Brak towaru
Brak towaru
Brak towaru
Kabel USB A 2.0/USB C silikonowy, 1m, czarny
Brak towaru
Puzzle 2,5D Lokomotywa Parowa to nie tylko atrakcja dla miłośników pociągów, ale również ciekawe wyzwanie dla modelarzy, łączące w sobie piękno i nostalgię epoki parowozów z innowacyjnym podejściem do prezentacji modeli. UGears 70207
Brak towaru
Brak towaru
Moduł kamery firmy ArduCam z autofocusem przeznaczony dla Raspberry Pi. Został wyposażony w matrycę (Sony IMX219) o rozdzielczości 8 MPix oraz zintegrowany filtr IR. Do podłączenia kamery z Raspberry Pi jest realizowane za pomocą złącza CSI. Autofocus pozwala na ostrzenie w zakresie od 4 cm do nieskończoności. ArduCAM B0122
Brak towaru
Brak towaru
KAmodWS2812-8 to moduł z ośmioma diodami wielokolorowymi WS2812. Dzięki wbudowanemu w każdą diodę sterownikowi, możliwe jest szeregowe łączenie modułów, uzyskując tym samym np. efektowne węże świetlne. KAmodWS2812-8
Brak towaru
Banana Pi R2 to minikomputer (router) wyposażony w czterordzeniowy procesor MediaTek MT7623N Quad-core ARM Cortex-A7, 2 GB pamięci RAM, moduł WiFi, Bluetooth 4.1 oraz złącza: HDMI, 5 x Ethernet, 2x USB 3.0. Zestaw posiada wyprowadzone złącze GPIO 40-pin, na którym można znaleźć interfejsy UART, SPI, I2C oraz ID EEPROM.
Brak towaru
Zmontowany bałwanek LED. AVT3150 C
Brak towaru
Brak towaru
Płytka PCB i zaprogramowany układ do 4-kanałowego termometru cyfrowego. AVT3085 A+
Brak towaru
Fully programmable card (PICC) emulator, simulator to characterize, test and certify contactless readers for ISO 14443, ISO 15693, NFC and FeliCa conformity
Brak towaru
Low-Cost, Micropower, Low-Dropout, High-Output-Current, 3V Voltage Reference, SOT23, Maxim, RoHS
Brak towaru
Zetaw AVT do samodzielnego montażu animowanej choinki LED 3D. AVT1988 B
Brak towaru
KIT-13199