List of products by brand Adafruit

Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5477

Board with RP2040 microcontroller and MCP2515 CAN controller. It has a built-in LiPo charging circuit and a STEMMA QT connector. It allows you to add communication based on the CAN bus to the project, commonly used in projects related to robotics and the automotive industry. Adafruit 5724

Module with digital barometer BMP390. It enables pressure measurement from 300 to 1250 hPa and temperature from -40℃ to 85℃. Communicates via I2C or SPI. Adafruit 4816

LCD panel with the possibility of controlling its transparency. Can block up to about 95% of incident light. Adafruit 3330

Module with the PAM8904 controller designed specifically to control piezoelectric elements. The amplifier operates over a wide frequency range, up to 300 kHz, and allows for gain up to approximately 13 Vpp. Adafruit 5791

Module with proximity and ambient light sensor based on the VCNL4020 system. It allows you to detect obstacles in the range from 0 to 20 cm and measure light intensity from 0.26 to 16,000 lux. It communicates via the I2C bus. Adafruit 5810

Module with light intensity sensor LTR-303. It offers a measuring range from 1 to 65535 lux and a 16-bit resolution. Communication takes place using I2C. Adafruit 5610

Adafruit 2348

The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. The power pin provides the 5V @ 500mA direct from the USB port and the RX/TX pins are 3.3V level for interfacing with the most common 3.3V logic level chipsets. Adafruit 954

Module with MEMS microphone; model SPW2430 with built-in amplifier. The plate also has a 3.3 V voltage stabilizer needed to power the microphone. Adafruit 2716

Panel voltage and current meter with LCD display. The meter allows to measure voltage in the range of 6.5-100V DC and current intensity up to 20 A. Additionally, the display can read information about the power consumed by the device, connected to the meter and the amount of energy consumed [Wh]. Adafruit 3626

This sensor communicates over I2C or SPI (our library code supports both) so you can share it with a bunch of other sensors on the same I2C bus. Adafruit 2809

This little PCB sits on top of the Pro Trinket and allows a LiPoly/LiIon battery to plug in. When the Pro Trinket USB port is powered, the battery is recharged automatically. Adafruit 2124

Module with a light intensity sensor LTR-329. It offers a measuring range from 1 to 65535 lux and a 16-bit resolution. Communication takes place using I2C. Adafruit 5591

Panel Mount USB Cable - B Female to Micro-B Male, length 280mm, RoHS

Module with connector designed for 40-pin TFT displays. It allows for simple connection of the display and control using pin-outs with a convenient raster. Adafruit 1932

Module with ToF VL53L4CX sensor with a range of up to 6 m. It is equipped with a STEMMA QT connector and communicates via the I2C interface. Adafruit 5425

The board is equipped with ATSAME51 microcontroller (ARM Cortex-M core) with CAN bus and SPI Flash memory, GPIO pins and a connector for connecting the battery with the charging circuit. Adafruit 4759

USB - UART converter based on the CH9102F chip. Compatible with the voltage of 3.3 V and 5 V, it has been equipped with a USB type C connector. Adafruit 5568

Air quality sensor module based on the SGP40 system. It uses CMOSens technology by Sensirion and provides information on the concentration of volatile organic compounds (VOC). Adafruit 4829