The KAmod USB-Micro Adapter Module allows for the connection of a Micro-USB port to almost any electronic system. All necessary signals are available on the pin header, including 5V power, D+ and D- data lines, and an additional ID signal.

KAmod TPS5401 is a compact Step-Down switching regulator based on the energy-efficient TPS5401 chip, providing an output voltage of 3.3 V, 5 V, or 12 V (depending on the version). It supports a maximum continuous current of 0.5 A and a wide input voltage range of 4...42 V, while its 2.54 mm pitch terminals allow for easy mounting.

The KAmod USB-Micro Adapter Module allows for the connection of a Micro-USB port to almost any electronic system. All necessary signals are available on the pin header, including 5V power, D+ and D- data lines, and an additional ID signal.

Development kit with STM32L496ZGT6 microcontroller (ARM Cortex-M4 core) with a built-in ST-Link programmer. Extensive equipment, including: MEMS 6DoF sensor, motor controller, joystick, LED display, 8 LED diodes, RGB LED, audio amplifier, Flash memory QSPI 1 MB, microphone, Arduino connector

KAmod USB-UART-mini is a compact USB-C to UART converter, based on the FT230XS chip, enabling communication at speeds from 300 bps to 3 Mbps and providing the option of mounting using an additional front panel; includes LED indicators, supports signal voltages of 3.3 V, optionally 5 V, and offers support for Windows, Linux and Mac

RJ12 6-Pin PH 10-Pin IDC Adapter for PIC Microcontrollers Programming

The KAmod BlackPill 401 is an evaluation board with an STM32F401CCU microcontroller, featuring USB-C with ESD protection and a modified power circuit. With a pre-installed bootloader, it supports Arduino IDE, offering 32 GPIOs and versatile programming capabilities

Miniature 15 V switching voltage regulator based on the AP63200 IC, input range 3.5 - 32 V, output current up to 1 A (1.5 A peak), efficiency up to 90%, dimensions 18 x 11 mm. KAmod-DCDC-AP63200 15V

The dual-channel KAmod Motor Driver TB6612FNG with MOSFET H-bridges enables precise control of DC and stepper motors with PWM frequency up to 100 kHz. The compact design, wide voltage range, and protections make the module suitable for mobile projects, robotics, and automation.

Evaluation board for STM32F103 microcontrollers

JTAG interface galvanic separator that protects equipment against damage caused by potential differences, with a maximum clock frequency of 110 MHz, 3-5 V power supply, and isolation voltage up to 1 kVDC, equipped with multiple connectors and optical status signaling

Development kit with STM32L496ZGT6 microcontroller with built-in ST-Link programmer. Extensive equipment, including: MEMS 6DoF sensor, motor controller, joystick, LED display, 8 LED diodes, RGB LED, audio amplifier, Flash memory QSPI 1 MB, microphone.

The KAmod SPI Flash module with the W25Q80 chip is a compact solution for memory expansion in embedded projects, data logging systems, configuration buffers, and applications requiring independent storage space. Its standard pin pitch allows easy use in prototyping and quick connection to popular microcontrollers supporting the SPI interface.

Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.

The KAmod ESP32-C3 board, equipped with a RISC-V microcontroller and a set of MEMS and SHTC3 sensors, enables the creation of IoT, measurement, and control applications. Thanks to power from USB-C or a battery and support for Arduino and Rust, it works perfectly in mobile projects and embedded systems.

Base board for dipPLD modules with XC2C256 (CoolRunner-II by Xilinx)

KAmod TPS5401 is a compact Step-Down switching regulator based on the energy-efficient TPS5401 chip, providing an output voltage of 3.3 V, 5 V, or 12 V (depending on the version). It supports a maximum continuous current of 0.5 A and a wide input voltage range of 4...42 V, while its 2.54 mm pitch terminals allow for easy mounting.

The KAmod USB-C Adapter Module allows for the connection of a USB-C port to almost any electronic system. The pin header provides only the essential signals, including 5V power and D+ and D- data lines.

The KAmod USB-C Adapter Module allows for the connection of a USB-C port to almost any electronic system. The pin header provides only the essential signals, including 5V power and D+ and D- data lines.

JTAG interface for microcontrollers with ARM core