KAmodRPi CAN-FD CAN interface compatible with CAN 2.0 and CAN FD for Raspberry Pi and more
search
  • KAmodRPi CAN-FD CAN interface compatible with CAN 2.0 and CAN FD for Raspberry Pi and more
  • KAmodRPi CAN-FD CAN interface compatible with CAN 2.0 and CAN FD for Raspberry Pi and more
  • KAmodRPi CAN-FD CAN interface compatible with CAN 2.0 and CAN FD for Raspberry Pi and more
  • KAmodRPi CAN-FD CAN interface compatible with CAN 2.0 and CAN FD for Raspberry Pi and more
  • KAmodRPi CAN-FD CAN interface compatible with CAN 2.0 and CAN FD for Raspberry Pi and more
ID: 1189248
5906623481477
zł69.77
Tax included

zł56.72 tax excl.

Versatile CAN bus interface based on the MCP2518FD controller, enabling communication in CAN 2.0 and CAN FD modes via SPI interface, compatible with SBC computers, including Raspberry Pi 5, with additional security and the ability to support two modules simultaneously

24h
Available
Available quantity: 49

Description

KAmod CAN-FD is a complete CAN bus interface based on an advanced CAN controller type MCP2518FD. The system used is responsible for forming correct frames sent to the bus, and buffering data sent to and from the CAN bus. Thanks to these features, it can work with almost any SBC computer or microcontroller. Communication on the CAN side can take place at a speed of up to 1 Mbps in CAN 2.0 mode or up to 8 Mbps in CAN FD mode. Communication with the controller takes place via a 4-wire SPI interface (MISO, MOSI, SCK, CE) and an additional interrupt signal (INT). All signals are fed to a 40-pin connector so that 2 modules can operate simultaneously with one Raspberry Pi 5 computer.

Features

  • CAN bus interface, compatible with CAN 2.0 and CAN FD
  • Based on the MCP2518FD CAN controller
  • Communication via SPI interface with a maximum clock speed of 20 MHz
  • SPI interface operating at 3.3 V or 5 V
  • Communication speed (bit rate): 125 kbps...1 Mbps (500 kbps...8 Mbps in FD mode)
  • Attached 120 Ω terminating resistor
  • LEDs indicating correct power supply and communication
  • Compatible with Raspberry Pi 5 and Raspberry Pi Zero boards
  • Possibility to connect two modules to one computer (communication via one SPI interface with separate CE0/CE1 lines)
  • CAN bus lines connected via Phoenix MC 3.81 mm connector
  • Protection against overvoltages on CAN bus lines
  • Power supply 5 V, 100 mA
  • Dimensions of the board 65x30 mm, height approx. 25 mm

Included

  • Assembled and activated module
  • Set of screws and spacers enabling screwing the overlay to the Raspberry board
1189248

Data sheet

Compatible with
Raspberry Pi 5/4/3/2/1 A/B, Zero/Zero 2 H/WH

Manufacturer

  • BTC Korporacja sp. z o. o.
  • Ludwinowo Zegrzyńskie 52G
  • 05-140 Ludwinowo Zegrzyńskie
  • Poland
  • [email protected]
  • 22 767 36 20

Responsible person

  • BTC Korporacja sp. z o. o.
  • Ludwinowo Zegrzyńskie 52G
  • 05-140 Ludwinowo Zegrzyńskie
  • Poland
  • [email protected]
  • 22 767 36 20

You might also like

Other products in the same category (16)