- Obecnie brak na stanie
Wires with Pre-crimped Terminals 50-Piece Rainbow Assortment F-F 6"
These premium wires are stranded 26AWG wires with female terminals on both ends. Together with our 0.1" crimp connector housings, these wires can be used to make custom cables with 0.1" (2.54mm) connectors. The assortment of 6" (15 cm) wires includes five each of ten different colors.
![]() |
| 0.1" connector custom cable. |
|---|
These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connector housings on the ends. By combining these wires with our crimp connector housings, you can quickly and easily create custom cables with 0.1" (2.54mm) connectors that mate with various 0.1"-spaced connectors, including male and female headers and solderless breadboards. Just pick the housing for the correct number of pins, pick the colors and genders for your wires, and snap them into the housings (note: it’s not easy to get the wires back out, so plan carefully!). No soldering is required!
You can easily make cable harnesses or assemblies that branch from one connector on one side to multiple connectors on the other (an example of this is shown in the picture to the right); you can also cut off one pre-crimped end and solder the wires directly to components to make swapping connections easy, as shown in the motor picture below.
The wires are available in six lengths—3" (7.5 cm), 6" (15 cm), 12" (30 cm), 24" (60 cm), 36" (90 cm), and 60" (150 cm)—and in ten colors:
![]() |
| 0.1" connector custom motor cable. |
|---|
These are the same colors as those used on resistor color codes and rainbow ribbon cable. The wire packs of different lengths include different quantities of wires. The table below shows the quantity included for a particular length-color combination:
| length | monochromatic pack quantity | rainbow pack quantity |
|---|---|---|
| 3" | – | 50 (5 of each color) |
| 6" | 10 | 50 (5 of each color) |
| 12" | 10 | 50 (5 of each color) |
| 24" | 5 | 50 (5 of each color) |
| 36" | 5 | 20 (2 of each color) |
| 60" | 2 | 10 (1 of each color) |
These wires can be purchased with male terminals on both ends, female terminals on both ends, or one male and one female terminals. These crimped terminals are designed for use with 0.1" (2.54 mm) male headers and female headers, solderless breadboards, and prototyping PCBs. Note that we also sell the crimp pins by themselves if you want to crimp your own wires.
![]() |
![]() |
| Female crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
| Male crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x2-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x1-Pin 25-Pack |
Producent
Osoba odpowiedzialna
Zmontowany zestaw AVT, bożonarodzeniowa, świecąca choinka LED. AVT1844 C
Brak towaru
Czujnik do wykrywania niebezpiecznego tlenku węgla i czadu, sygnalizuje wyciek gazu i obecność czadu w pomieszczeniach. URZ0409
Brak towaru
Kabel żeńsko-żeński 10-żyłowy połączeniowy o długości 15 cm ze złączami o rastrze 1,27 mm. Adafruit 1675
Brak towaru
Brak towaru
Karta pamięci Kingston micro SD 32GB class 4 z adapterem
Brak towaru
Moduł czujnika temperatury oparty o układ TCN75A. Digilent 410-287
Brak towaru
Moduł wyposażony w układ DRV8833 pozwalający sterować dwoma silnikami DC lub jednym krokowym. Digilent 410-259
Brak towaru
Zestaw uruchomieniowy chipKIT DP32 wyposażony w mikrokontroler PIC32MX250F128B (40/50 Mhz, 128 kB Flash, 32 kB RAM), obszar prototypowy z polami lutowniczymi, potencjometr, 4 diody LED, 2 przyciski oraz pola lutownicze dla pamięci EEPROM i analogowego czujnika temperatury. Digilent 410-280P-KIT
Brak towaru
Płytka rozszerzająca zgodna ze złączem myRIO Expansion Port (MXP) oferująca obszar prototypowy 14x21 pól lutowniczych. Digilent 6002-210-008P
Brak towaru
Zestaw elementów i układów elektronicznych zawierający m.in. wzmacniacze operacyjne, stabilizatory, bramki i inne układy logiczne, przetworniki, tranzystory, rezystory, diody, kondensatory. Digilent 6002-240-001P-KIT
Brak towaru
Prototypowa płytka stykowa posiadająca 1260 punktów przeznaczona jest w szczególności do wykorzystania z zestawami NI myDAQ i NI myRIO. Posiada złącze Mini System Port (MSP). Digilent 6002-410-006
Brak towaru
Kabel 6-żyłowy o długości 15 cm dla modułów Pmod firmy Digilent. Pmod Cable Kit 6-pin (240-021-6)
Brak towaru
Płytka bazowa Arduino Yun z mikrokontrolerem ATmega32u4 z modułem Linino WiFi. Płytka wspiera technologię Power over Ethernet (PoE). A000003
Brak towaru
Płytka startowa LPCXpresso4337 z dwurdzeniowym mikrokontrolerem LCP4337 (Cortex-M4F + Cortex-M0+). Zestaw wyposażony jest we wbudowany programator, przyciski, diodę, pamięć quad SPI Flash oraz konwetrer USB - UART
Brak towaru
Płytka startowa LPCXpresso18S37 z mikrokontrolerem LPC18S37 (Cortex-M3). Zestaw wyposażony jest we wbudowany programator, przyciski, diodę, pamięć quad SPI Flash oraz konwetrer USB - UART
Brak towaru
Belka tensometryczna aluminiowa, pozwalająca na pomiar masy do 100 kilogramów. Posiada cztery przewody. Znajduje zastosowanie w wagach kuchennych oraz wagach przenośnych, max 100 kg, 20x23x94, przewód 21 cm, RoHS
Brak towaru
Wires with Pre-crimped Terminals 50-Piece Rainbow Assortment F-F 6"