- Out-of-Stock
These premium wires are stranded 26AWG wires with female terminals on both ends. Together with our 0.1" crimp connector housings, these wires can be used to make custom cables with 0.1" (2.54mm) connectors. The assortment of 6" (15 cm) wires includes five each of ten different colors.
![]() |
| 0.1" connector custom cable. |
|---|
These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connector housings on the ends. By combining these wires with our crimp connector housings, you can quickly and easily create custom cables with 0.1" (2.54mm) connectors that mate with various 0.1"-spaced connectors, including male and female headers and solderless breadboards. Just pick the housing for the correct number of pins, pick the colors and genders for your wires, and snap them into the housings (note: it’s not easy to get the wires back out, so plan carefully!). No soldering is required!
You can easily make cable harnesses or assemblies that branch from one connector on one side to multiple connectors on the other (an example of this is shown in the picture to the right); you can also cut off one pre-crimped end and solder the wires directly to components to make swapping connections easy, as shown in the motor picture below.
The wires are available in six lengths—3" (7.5 cm), 6" (15 cm), 12" (30 cm), 24" (60 cm), 36" (90 cm), and 60" (150 cm)—and in ten colors:
![]() |
| 0.1" connector custom motor cable. |
|---|
These are the same colors as those used on resistor color codes and rainbow ribbon cable. The wire packs of different lengths include different quantities of wires. The table below shows the quantity included for a particular length-color combination:
| length | monochromatic pack quantity | rainbow pack quantity |
|---|---|---|
| 3" | – | 50 (5 of each color) |
| 6" | 10 | 50 (5 of each color) |
| 12" | 10 | 50 (5 of each color) |
| 24" | 5 | 50 (5 of each color) |
| 36" | 5 | 20 (2 of each color) |
| 60" | 2 | 10 (1 of each color) |
These wires can be purchased with male terminals on both ends, female terminals on both ends, or one male and one female terminals. These crimped terminals are designed for use with 0.1" (2.54 mm) male headers and female headers, solderless breadboards, and prototyping PCBs. Note that we also sell the crimp pins by themselves if you want to crimp your own wires.
![]() |
![]() |
| Female crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
| Male crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x2-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x1-Pin 25-Pack |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The device for automatic control of lighting or other electrical devices. Installed in place of an ordinary wall switch. He reacts to movement
No product available!
Patchcord UTP 5E Ethernet cable with a length of 50 cm - gray, with 2xRJ45 connectors
No product available!
Pre-installed Android5.x or latest version. eMMC Version 5.0 interface or higher version from Samsung. JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode. The eMMC chipset is only compatible with Amlogic S905 and S805 series(ODROID-C1+ / C0 / C2)
No product available!
No product available!
No product available!
Minicomputer with Allwinner H3 quad-core processor and 1 GB RAM. It has a WiFi and BT module, two Ethernet ports, 2 USB 2.0 ports and a microUSB and a microSD slot. FriendlyELEC NanoPi R1
No product available!
The second version of the clock synchronization signal receiver, transmitted with AM modulation (DCF77). The built-in MAS6180 system allows you to receive timing frames from a time pattern using a carrier frequency of 77.5 kHz. Thanks to this module, it is possible to create a clock with automatic date and time synchronization. The module has a ferrite antenna. modDCF77 v2
No product available!
No product available!
No product available!
No product available!
No product available!
Turnigy HAL (Heavy Aerial Lift) - hexagon frame 775 mm (HK25698)
No product available!
Camera module with IMX219 sensor with a resolution of 8 MP equipped with programmable focus, without IR filter. Designed for NVIDIA Jetson Nano and Raspberry Pi CM. ArduCAM B0189
No product available!
Green, aluminum case for Raspberry Pi 4 model B. It has been equipped with mounting holes of the VESA 75 standard
No product available!
No product available!