- Obecnie brak na stanie

35:1 Mini Metal Gearmotor
35:1 Mini Metal Gearmotor
This gearmotor is a compact (1.50" x 0.59" x 0.47") brushed DC motor with 35:1 metal gearbox. These units have a 0.365"-long, 3 mm-diameter D-shaped output shaft that matches the micro metal gearmotor output shafts.
Key specs at 6 V: 350 RPM and 70 mA free-run, 20 oz-in (1.4 kg-cm) and 1.5 A stall.
This brushed DC motor has a long (0.365" or 9.27 mm, not 8mm as shown in the drawing below), 3 mm-diameter D-shaped metal output shaft that matches our assortment of Pololu wheels and the Solarbotics RW2 rubber wheel. Alternatively, you can use the Pololu universal mounting hub to mount custom wheels and mechanism to the micro metal gearmotor’s output shaft.
The brass faceplate has two mounting holes threaded for M2 screws (2 mm diameter, 0.4 mm thread pitch).
Note: this gearmotor is not compatible with our Sanyo-style micro gearmotor mounting brackets (products 989 and 1089).
![]() |
35:1 mini metal gearmotor dimensions (units in mm). |
---|
|
|
|
These motors are intended for use at 9 V, which means you can get more speed and torque out of this motor than is listed in the 6 V specs. In general, these kinds of motors can run at voltages above and below this nominal voltage, so they should comfortably operate in the 3 – 12 V range (the motor can begin rotating at voltages as low as 0.5 V). Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.
At 6 V, this gearmotor will have a no-load RPM of around 350 with a free-run current of 70 mA, a stall current of 1.5 A, and a stall torque of around 14 oz-in (1 kg-cm).
We offer a wide selection of metal gearmotors that offer different combinations of speed and torque. Our metal gearmotor comparison table can help you find the motor that best meets your project’s requirements.
![]() |
Some of the Pololu metal gearmotors. |
---|
![]() |
100:1 Micro Metal Gearmotor HP |
![]() |
50:1 Micro Metal Gearmotor HP |
![]() |
Pololu Wheel 42x19mm Pair |
Cechy
Wyświetlacz graficzny 192x64, 100x60mm, STN NEGATIVE-BLUE, podświetlaniem LED (White), sterownik zgodny z KS0108A
Brak towaru
Brak towaru
Brak towaru
Filament firmy ROSA3D wykonany z wysokiej jakości granulatu PLA. Na szpuli nawinięte jest 0,8 kg filamentu o średnicy 1,75 mm. ROSA3D PLA Starter Natural Transparent
Brak towaru
Płytka rozwojowa oparta na MCU GD32VF103CBT6 z 32-bitowym rdzeniem RISC-V. Wyposażony został w wyświetlacz LCD IPS RGB o przekątnej 0,96 cala 160x80 i obudowę. Seeed Studio 102991302
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Zestaw uruchomieniowy dla mikrokontrolerów ST7LITE
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Brak towaru
ZL8ARM (dipARM_2106P) - moduł DIP z mikrokontrolerem LPC2106 i programatorem IAP
Brak towaru
Brak towaru
35:1 Mini Metal Gearmotor