- Out-of-Stock

35:1 Mini Metal Gearmotor
35:1 Mini Metal Gearmotor
This gearmotor is a compact (1.50" x 0.59" x 0.47") brushed DC motor with 35:1 metal gearbox. These units have a 0.365"-long, 3 mm-diameter D-shaped output shaft that matches the micro metal gearmotor output shafts.
Key specs at 6 V: 350 RPM and 70 mA free-run, 20 oz-in (1.4 kg-cm) and 1.5 A stall.
This brushed DC motor has a long (0.365" or 9.27 mm, not 8mm as shown in the drawing below), 3 mm-diameter D-shaped metal output shaft that matches our assortment of Pololu wheels and the Solarbotics RW2 rubber wheel. Alternatively, you can use the Pololu universal mounting hub to mount custom wheels and mechanism to the micro metal gearmotor’s output shaft.
The brass faceplate has two mounting holes threaded for M2 screws (2 mm diameter, 0.4 mm thread pitch).
Note: this gearmotor is not compatible with our Sanyo-style micro gearmotor mounting brackets (products 989 and 1089).
![]() |
35:1 mini metal gearmotor dimensions (units in mm). |
---|
|
|
|
These motors are intended for use at 9 V, which means you can get more speed and torque out of this motor than is listed in the 6 V specs. In general, these kinds of motors can run at voltages above and below this nominal voltage, so they should comfortably operate in the 3 – 12 V range (the motor can begin rotating at voltages as low as 0.5 V). Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.
At 6 V, this gearmotor will have a no-load RPM of around 350 with a free-run current of 70 mA, a stall current of 1.5 A, and a stall torque of around 14 oz-in (1 kg-cm).
We offer a wide selection of metal gearmotors that offer different combinations of speed and torque. Our metal gearmotor comparison table can help you find the motor that best meets your project’s requirements.
![]() |
Some of the Pololu metal gearmotors. |
---|
![]() |
100:1 Micro Metal Gearmotor HP |
![]() |
50:1 Micro Metal Gearmotor HP |
![]() |
Pololu Wheel 42x19mm Pair |
Data sheet
A 12-in-1 construction set that teaches the use of solar and hydraulic energy. KSR17
No product available!
No product available!
The official power supply for Raspberry Pi with 5.1V output voltage and 2.5A current efficiency. White power supply.
No product available!
A module with Acconeer sensor A111. A111 is a one-chip radar (PCR) solution complete with antennas and SPI interface up to 50 MHz. SparkFun Pulsed Radar Breakout A111
No product available!
Decoder for receiving digital terrestrial TV programs in the DVB-T2 H.265 standard. Equipped with HDMI, SCART, RF, USB and RJ45 connectors
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
MP3 player module controlled by the I2C interface. It is based on a class D amplifier with a power of 1.4 W. The board has a 3.5 mm headphone output and an 8 Ω speaker connector. Audio files are saved on the microSD card. SparkFun DEV-15165
No product available!
Side panel with I/O elements for Totem Mini Lab and Totem Micro Lab sets. There are buttons, potentiometers, LED diodes and a relay on the board. Totem TE-SP01-B
No product available!
Diode / RGB controller with 12V supply voltage and 10A maximum current consumption. The controller supports 11 programs, the control takes place from the level of a convenient radio remote control with a telescopic antenna. ALM LED-RGB-CONTROLLER
No product available!
No product available!
No product available!
No product available!
35:1 Mini Metal Gearmotor