- Out-of-Stock
New products
New products New products
zł119.00
Delivery date unknown
zł119.00
Delivery date unknown
bAVT5378 A
ID: 208662
DIFFERENTIAL MEASURING PROBE WITH GALVANIC INSULATION - PRINTED PLATE
DIFFERENTIAL MEASURING PROBE WITH GALVANIC INSULATION - PRINTED PLATE
Producer: AVT
By using a differential measuring probe, only the signal controlling the gates of the MOSFET transistors is fed to the oscilloscope input. At the same time, you can observe waveforms on different potentials (low-side and high-side), and thanks to galvanic isolation you do not need to use a transformer on the power supply.
Recommendations: a practical, inexpensive solution for the measuring probe, which will be useful for all designers dealing with devices for power electronics.
Basic information:
- input voltage: -20V ... + 20V
- input impedance: 1 MV / ~ 10 pF
- measuring band: DC ... 134 kHz (drop 0.5 dB) ... 633 kHz (drop 3dB)
- delay of the rising / falling edge: about 500 ns / ok. 500 ns
- processing factor: approx. 200: 1 (10V -> 50mV)
- maximum input voltage:? 100 V
- power supply: 4 R6 (AA) batteries
- power consumption: 19mA (input circuit), 200mA (output circuit)
- a printed circuit board and documentation in the set
A detailed description in EP1 / 13 or 
208662
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
The minicomputer with the Intel Celeron J4115 quad-core processor (2.5 GHz, 64-bit) has 2 slots for DDR4 RAM modules. Additionally, it is equipped with, among others: Gigabit Ethernet, HDMI 2.0 port and Display Port 1.2 4K/60Hz, four USB sockets, 24 GPIO, PCI-e slot, two SATA3 connectors. Rev-B+. ODROID H2+
Retired
No product available!
No product available!
A new version is available: VisionCB-STD v.2.0.
VisionCB-STD is a base board for VisionSOM-6UL (i.MX6 UL) and VisionSOM-6ULL (i.MX6 ULL) modules. The tile contains, among others Ethernet, USB connectors, connectors compatible with Arduino shields and Raspberry Pi hat, 5 buttons and 5 LEDs. VisionCB-STD
Delivery date unknown
No product available!
High voltage differential probe. It has good measurement parameters: 100 MHz band and operating voltage up to 1300 V. The probe has two damping factors: 50X and 500X. Micsig DP10013
Retired
No product available!
No product available!
Following the modern trend of minimalistic and functional design, Ugears is proud to present a new clever and practical addition to their collection of wooden mechanical models, the Foldable Phone Holder of the Mini-series.
Clean lines and functionality coupled with Ugears iconic design was the main ground on which the idea of the foldable phone stand was born and developed. UGears 70145
Retired
No product available!
The module with an RFID reader designed for the M5Stack sets. Based on the MFRC522 chip, it supports popular protocols: ISO14443A, MIFARE and NTAG. M5Stack U031
Retired
No product available!
No product available!
Micro SD 16GB class 10 card with NOOBS for RPi
Retired
No product available!
Read/Write analog front end for 125 kHz RFID Basestation, SOIC16, EM Microrlectronic, RoHS
Retired
No product available!
ROSA3D filament made of high quality PVB. 0.5 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PVB Smooth Red
Retired
No product available!
No product available!
No product available!
No product available!
No product available!
Kit for building an intelligent JetBot robot based on Jetson Nano. It consists of Jetson Nano with 2GB RAM, expansion module, WiFi card, camera, motors, housing and a set of mounting screws. JetBot AI Kit (USB WiFi) 2GB
Retired
No product available!
DIFFERENTIAL MEASURING PROBE WITH GALVANIC INSULATION - PRINTED PLATE