- Obecnie brak na stanie
![Pololu 798 - Pololu 5V Boost Regulator NCP1402 Pololu 798 - Pololu 5V Boost Regulator NCP1402](https://kamami.pl/8106-large_default/pololu-798-pololu-5v-boost-regulator-ncp1402.jpg)
Pololu 5V Boost Regulator NCP1402
darmowa wysyłka na terenie Polski dla wszystkich zamówień powyżej 500 PLN
Jeśli Twoja wpłata zostanie zaksięgowana na naszym koncie do godz. 11:00
Każdy konsument może zwrócić zakupiony towar w ciągu 14 dni bez zbędnych pytań
Pololu 5V Boost Regulator NCP1402
This extremely compact boost regulator generates 5 V from voltages as low as 0.8 V and delivers up to 200 mA, making it perfect for powering small 5V electronics projects from 1 to 3 NiMH, NiCd, or alkaline cells or from a single lithium-ion cell.
![]() |
This tiny boost switching regulator is based on the NCP1402 boost regulator IC. Its small dimensions of just 0.33" x 0.5" (8.4 x 12.7 mm) and a startup voltage of down to 0.8 V make it easy to build 5 V circuits that are powered by lower battery voltages. The available output current and output voltage ripple depend on the input voltage. With a 0.8 V input, approximately 5 mA are available before the output voltage begins dropping. The full 200 mA output can be realized from input voltages over approximately 2.7 V. With low input voltages, the output voltage ripple is under 40 mV peak-to-peak; close to 5 V, the output ripple quickly climbs to 150 mV peak-to-peak. Therefore, adding capacitance from the output to ground is recommended for noise-sensitive applications with input voltages close to 5 V.
Some example applications include:
![]() |
The boost regulator has just three connections: the input voltage, ground, and the output voltage. These three connections are labeled on the back side of the PCB, and they are arranged with a 0.1" spacing along the edge of the board for compatibility with standard solderless breadboards and perfboards and connectors that use a 0.1" grid. You can solder wires directly to the board or solder in either the 3×1 straight male header strip or the 3×1 right-angle male header strip that is included.
![]() |
5V boost regulator NCP1402 schematic diagram. |
---|
![]() |
Pololu Pushbutton Power Switch LV |
![]() |
Pololu Adjustable Boost Regulator 2.5-9.5V |
![]() |
Pololu Adjustable Boost Regulator 4-25V |
Prosty w użyciu czujnik pola magnetycznego i przyśpieszenia, interfejs I2C lub SPI, zasilanie 2,5-5,5V, zakres pomiarowy magnetometru: ±2~±12Gs, zakres pomiarowy akcelerometru: ±2~±16g, kompatybilny z Arduino i Raspberry Pi. Pololu 2127
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Moduł AltIMU w wersji 3 zawiera czujniki L3GD20H, LSM303D oraz LPS331AP. Interfejs komunikacyjny I2C z dostępem do 10 wartości pomiarowych umożliwia określenie wysokości i pozycji modułu. Płytka zasilana jest napięciem z zakresu 2,5..5,5 V, złącze ma raster 0,1 cala. Pololu 2469
Brak towaru
Brak towaru
Kamera o rozdzielczości 5 MPx z interfejsem USB. Wyposażona w sensor CMOS OV5648 z szerokokątnym obiektywem o kącie widzenia 140°. ArduCAM U6073
Brak towaru
Brak towaru
Brak towaru
Moduł pamięci Flash eMMC 5.1 dla komputerów Odroid C2 firmy Hardkernel. Pojemność 32GB, zainstalowany system operacyjny Linux. W zestawie znajduje się adapter microSD. Hardkernel
Brak towaru
Bezprzewodowy czujnik temperatury o dużej dokładności z wbudowaną pamięci zdarzeń (rejestratorem) z przetwornikiem Si7051
Brak towaru
Brak towaru
Brak towaru
Zestaw z dwiema kamerami IMX219 o rozdzielczości 8 MP oraz modułem rozszerzeń dla Raspberry Pi, który pozwala na jednoczesne podłączenie dwóch kamer. ArduCAM B0350
Brak towaru
Terenowe podwozie Dagu Wild Thumper 6WD w kolorze srebrnym, w komplecie koła o średnicy 120 mm oraz silniki z przekładnią 75:1. Podwozie jest wykonane z blachy aluminiowej, otwory o średnicy 4 mm rozmieszczone co 10 mm umożliwiają montaż kontrolera oraz akcesoriów. Pololu 1561
Brak towaru
Brak towaru
Pololu 5V Boost Regulator NCP1402