- Obecnie brak na stanie

These premium wires are stranded 26AWG wires with female terminals on both ends. Together with our 0.1" crimp connector housings, these wires can be used to make custom cables with 0.1" (2.54mm) connectors. The assortment of 24" (60 cm) wires includes five each of ten different colors.
![]() |
0.1" connector custom cable. |
---|
These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connector housings on the ends. By combining these wires with our crimp connector housings, you can quickly and easily create custom cables with 0.1" (2.54mm) connectors that mate with various 0.1"-spaced connectors, including male and female headers and solderless breadboards. Just pick the housing for the correct number of pins, pick the colors and genders for your wires, and snap them into the housings (note: it’s not easy to get the wires back out, so plan carefully!). No soldering is required!
You can easily make cable harnesses or assemblies that branch from one connector on one side to multiple connectors on the other (an example of this is shown in the picture to the right); you can also cut off one pre-crimped end and solder the wires directly to components to make swapping connections easy, as shown in the motor picture below.
The wires are available in six lengths—3" (7.5 cm), 6" (15 cm), 12" (30 cm), 24" (60 cm), 36" (90 cm), and 60" (150 cm)—and in ten colors:
![]() |
0.1" connector custom motor cable. |
---|
These are the same colors as those used on resistor color codes and rainbow ribbon cable. The wire packs of different lengths include different quantities of wires. The table below shows the quantity included for a particular length-color combination:
length | monochromatic pack quantity | rainbow pack quantity |
---|---|---|
3" | – | 50 (5 of each color) |
6" | 10 | 50 (5 of each color) |
12" | 10 | 50 (5 of each color) |
24" | 5 | 50 (5 of each color) |
36" | 5 | 20 (2 of each color) |
60" | 2 | 10 (1 of each color) |
These wires can be purchased with male terminals on both ends, female terminals on both ends, or one male and one female terminals. These crimped terminals are designed for use with 0.1" (2.54 mm) male headers and female headers, solderless breadboards, and prototyping PCBs. Note that we also sell the crimp pins by themselves if you want to crimp your own wires.
![]() |
![]() |
Female crimp pin for 0.1" housings crimped onto a wire. |
---|
![]() |
Male crimp pin for 0.1" housings crimped onto a wire. |
---|
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x2-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x4-Pin 10-Pack |
Producent BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Osoba odpowiedzialna BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Płytka drukowana do modułowego odbiornika nasłuchowego na pasma 80m i 40m Dosia. Filtry wejściowe w.cz. 40m/80m. AVT3190 A
Brak towaru
Drift Cobra Racing Car od UGears to wyjątkowy model, który oferuje nie tylko wspaniały wygląd, ale i ekscytujące możliwości mechaniczne. Idealny dla pasjonatów konstrukcji drewnianych i motoryzacji, gwarantuje satysfakcję z budowy oraz z jazdy. UGears 70161
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Ekspander funkcjonalny dla NUCLEO i Arduino z zestawem sensorów środowiskowych: ciśnienia, wilgotności, temperatury i natężenia światła oraz 5-pozycyjnym joystickiem i LED RGB.
Brak towaru
Brak towaru
Obudowa przeznaczona dla minikomputera Odroid-HC2. Góra obudowy została wykonana z czarnego plastiku
Brak towaru
Zestaw 50 szt. różnokolorowych przewodów żeńsko-żeńskich o długości 30 cm do płytek stykowych, raster 2,54 mm
Brak towaru
Płytka zgodna z Arduino UNO bazująca na układzie WiFi ESP32. Została zaprojektowana z myślą o współpracy z kamerami ArduCAM 2 MPx i 5 MPx. Posiada gniazdo na karty pamięci microSD. Może być zasilana z gniazda microUSB, złącza DC lub za pomocą akumulatora. ArduCAM B0105
Brak towaru
The 4.3" TFT LCD screen with 4-wire resistive touchscreen and five user button, RoHS
Brak towaru
Płyn do czyszczenia płytek drukowanych na bazie alkoholu izopropylowego, doskonale usuwa resztki polutownicze, jak również smary i oleje
Brak towaru
Brak towaru
Karta rozszerzająca dedykowana dla zestawów z serii DE FPGA firmy Terasic. Zawiera głownie elementy niezbędne do komunikacji (moduł Wi-Fi oraz Bluetooth) oraz czujniki (światła, wilgotności, temperatury, akcelerometr, żyroskop oraz magnetometr). Wbudowany konwerter UART <> USB umożliwia komunikacje z komputerem PC. Terasic P0499
Brak towaru
Brak towaru