- Obecnie brak na stanie

These premium wires are stranded 22AWG wires with female terminals on both ends. Together with our 0.1" crimp connector housings, these wires can be used to make custom cables with 0.1" (2.54mm) connectors. The assortment of 36" (90 cm) wires includes two each of ten different colors.
![]() |
0.1" connector custom cable. |
---|
These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connector housings on the ends. By combining these wires with our crimp connector housings, you can quickly and easily create custom cables with 0.1" (2.54mm) connectors that mate with various 0.1"-spaced connectors, including male and female headers and solderless breadboards. Just pick the housing for the correct number of pins, pick the colors and genders for your wires, and snap them into the housings (note: it’s not easy to get the wires back out, so plan carefully!). No soldering is required!
You can easily make cable harnesses or assemblies that branch from one connector on one side to multiple connectors on the other (an example of this is shown in the picture to the right); you can also cut off one pre-crimped end and solder the wires directly to components to make swapping connections easy, as shown in the motor picture below.
The wires are available in six lengths—3" (7.5 cm), 6" (15 cm), 12" (30 cm), 24" (60 cm), 36" (90 cm), and 60" (150 cm)—and in ten colors:
![]() |
0.1" connector custom motor cable. |
---|
These are the same colors as those used on resistor color codes and rainbow ribbon cable. The wire packs of different lengths include different quantities of wires. The table below shows the quantity included for a particular length-color combination:
length | monochromatic pack quantity | rainbow pack quantity |
---|---|---|
3" | – | 50 (5 of each color) |
6" | 10 | 50 (5 of each color) |
12" | 10 | 50 (5 of each color) |
24" | 5 | 50 (5 of each color) |
36" | 5 | 20 (2 of each color) |
60" | 2 | 10 (1 of each color) |
These wires can be purchased with male terminals on both ends, female terminals on both ends, or one male and one female terminals. These crimped terminals are designed for use with 0.1" (2.54 mm) male headers and female headers, solderless breadboards, and prototyping PCBs. Note that we also sell the crimp pins by themselves if you want to crimp your own wires.
![]() |
![]() |
Female crimp pin for 0.1" housings crimped onto a wire. |
---|
![]() |
Male crimp pin for 0.1" housings crimped onto a wire. |
---|
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x2-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x1-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack |
Producent BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Osoba odpowiedzialna BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Listwa montażowa ARK 3-pinowa o rastrze 5,0 mm, rozłączalna. 301-5.0-03P-12-00A(H)-BL
Brak towaru
Brak towaru
Kamera o rozdzielczości 2 MPx z interfejsem USB. Wyposażona w sensor CMOS OV2710 z ruchomym filtrem IR i oświetleniem IR LED. ArduCam B0205
Brak towaru
Brak towaru
Pololu Micro Serial Servo Controller (assembled)
Brak towaru
Shield dla STM32 Nucleo z modułem WiFi b/g/n SPWF01SA. Firmware modułu pozwala na pracę jako klient oraz serwer UDP/TCP, serwer WWW, obsługuje protokoły TCP/IP, TLS/SSL. Dostępnych jest 16 linii GPIO
Brak towaru
Brak towaru
Zmontowany moduł miniaturowego zasilacza 5V. AVT1913/5 C
Brak towaru
Moduł DIP z mikrokontrolerem ARM LPC2138
Brak towaru
Brak towaru
Brak towaru
Prosty w użyciu moduł z 3-osiowym żyroskopem L3GD20, interfejs I2C lub SPI, zasilanie 2.5..5.5V, regulator napięcia wyjściowego 3.3V, regulowany zakres czułości ±250°/s, ±500°/s, lub ±2000°/s, kompatybilny z Arduino i Raspberry Pi. Pololu 2125
Brak towaru
Brak towaru
Brak towaru
9-kanałowy analizator stanów logicznych ScanaPLUS o częstotliwości próbkowania 100 MHz, do 256000 próbek na kanał, napięcie wejściowe ±24 V. ScanaPLUS ma możliwość generowania przebiegów logicznych. Współpracuje z systemami Windows, OS X oraz Linux
Brak towaru