- Out-of-Stock
These premium wires are stranded 22AWG wires with female terminals on both ends. Together with our 0.1" crimp connector housings, these wires can be used to make custom cables with 0.1" (2.54mm) connectors. The assortment of 36" (90 cm) wires includes two each of ten different colors.
![]() |
| 0.1" connector custom cable. |
|---|
These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connector housings on the ends. By combining these wires with our crimp connector housings, you can quickly and easily create custom cables with 0.1" (2.54mm) connectors that mate with various 0.1"-spaced connectors, including male and female headers and solderless breadboards. Just pick the housing for the correct number of pins, pick the colors and genders for your wires, and snap them into the housings (note: it’s not easy to get the wires back out, so plan carefully!). No soldering is required!
You can easily make cable harnesses or assemblies that branch from one connector on one side to multiple connectors on the other (an example of this is shown in the picture to the right); you can also cut off one pre-crimped end and solder the wires directly to components to make swapping connections easy, as shown in the motor picture below.
The wires are available in six lengths—3" (7.5 cm), 6" (15 cm), 12" (30 cm), 24" (60 cm), 36" (90 cm), and 60" (150 cm)—and in ten colors:
![]() |
| 0.1" connector custom motor cable. |
|---|
These are the same colors as those used on resistor color codes and rainbow ribbon cable. The wire packs of different lengths include different quantities of wires. The table below shows the quantity included for a particular length-color combination:
| length | monochromatic pack quantity | rainbow pack quantity |
|---|---|---|
| 3" | – | 50 (5 of each color) |
| 6" | 10 | 50 (5 of each color) |
| 12" | 10 | 50 (5 of each color) |
| 24" | 5 | 50 (5 of each color) |
| 36" | 5 | 20 (2 of each color) |
| 60" | 2 | 10 (1 of each color) |
These wires can be purchased with male terminals on both ends, female terminals on both ends, or one male and one female terminals. These crimped terminals are designed for use with 0.1" (2.54 mm) male headers and female headers, solderless breadboards, and prototyping PCBs. Note that we also sell the crimp pins by themselves if you want to crimp your own wires.
![]() |
![]() |
| Female crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
| Male crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x2-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x1-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
No product available!
No product available!
Pre-installed Ubuntu 14.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
No product available!
Pre-installed Android 4.x or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
No product available!
3.2D soldering tip, flat screwdriver 5.5mm in diameter, for WEP 926 soldering station
No product available!
Pre-installed Ubuntu 14.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
No product available!
5V / 3.1A eXtreme power supply with microUSB plug for all Raspberry Pi computers (including Pi 3 model B and Pi 3 model B +)
No product available!
Antenna with built-in LNA amplifier with high sensitivity, for mounting in a device using a GPS module. The antenna has a 25mm cable, terminated with a U.FL plug (IPEX). Dimensions of the device: 9 x 9 x 4mm
No product available!
The GY-GPS6MV1 module is a board containing the U-blox NEO-6M GPS receiver system. The tile also includes RTC backup battery, antenna connector (U.FL), voltage stabilizer and UART signal outputs
No product available!
Kit: MAXimator, MAXimator Expander, ZL32PRG - USB Blaster PRO
No product available!
Power Supply 2.5A 5.1V for Raspberry Pi 3 model B - STONTRONICS T5875DV
No product available!
MYD-JA5D44 Development Board is a complete educational platform. Its heart is the MYIR MYC-JA5D44 module, which was equipped with the Atmel SAMA5D44 processor based on Cortex-A5 cores. The processor can work at a maximum frequency of 600 MHz. Min. RS232, RS485 connectors, HDMI connector, 3.5 mm Jack Audio inputs, microSD memory card slot, 10/100 Mbps Ethernet slot and many more.
No product available!
The Raspberry Pi GPIO Triple Expansion Board converts the single GPIO headers on your Raspberry Pi into three parts. DFR0385
No product available!
Flex Cable for Raspberry Pi Camera - 300mm / 12". Adafruit 1648
No product available!
Comes with a 6"x6" (152mm x 152mm) square of Pyralux. It\'s ED-Y type copper at 35um (1 oz/ft2) and has a polymide of 25um (1 mil). The thick copper layer means it can carry a lot of current, and its trivial to solder to it. Adafruit 1894
No product available!
Patchcord UTP 5E Ethernet cable with a length of 50 cm - gray, with 2xRJ45 connectors
No product available!