- Obecnie brak na stanie

Rechargeable NiMH Battery Pack: 6.0 V, 200 mAh, 3+2 1/3-AAA Cells, JR Connector
This is a rechargeable 6.0 V NiMH battery pack with a capacity of 200 mAh. The pack consists of five 1/3-size AAA cells in two rows and a 4" lead terminated by a “JR”-style connector.
![]() |
This battery pack comes with 4" leads terminated by a 3-pin JR-style female connector (only two of the pins are used). The connector is the same as what is found on the most servos and has a 0.1" spacing, so it fits nicely with 0.1" male headers and can plug directly into most RC receivers, servo extension cables, and servo switch harnesses, and custom cables made with JR male connectors or Futaba J male connectors. Note, however, that this style of connector is often referred to as “male” in the RC hobby industry, so please use the picture on the right to clear up any potential confusion.
Our rechargeable NiMH battery packs give you variety of options for powering your robot or electronics project. The battery packs use 1.2 V cells and are available in several capacities:
![]() |
Cell Type | Capacity (mAh) |
---|---|
AA | 2200 |
AAA | 900 |
2/3 AAA | 350 |
1/3 AAA | 200 |
The picture to the right shows the relative sizes of our NiMH battery packs. These packs are well-suited for powering small robots, and the smaller (1/3- or 2/3-AAA) battery packs make great power sources for miniature robots, such as those that might be based on our Baby Orangutan robot controller.
|
|
Battery pack color may differ from what is shown in the main product picture.
Note: The battery voltages listed in the product descriptions are based on the 1.2 V nominal voltage of the NiMH cells from which the packs are made. The actual voltage will depend on how charged the batteries are. A fully charged NiMH cell will deliver almost 1.5 V, so, for example, a “6V”, 5-cell pack can measure over 7 volts after being charged, and it can fall well below 5 volts when the pack is drained. You will need to charge these battery packs before you first use them. The iMAX-B6AC battery charger works well with these battery packs.
Producent BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Osoba odpowiedzialna BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Płytka rozwojowa FPGA PYNQ-Z1 oraz zestaw akcesorów. Zawiera płytkę bazową, zasilacz, przewody oraz kartę SD z obrazem systemu dla PYNQ-Z1. Wersja akademicka. Digilent 240-114-1
Brak towaru
Arty Artix-7 FPGA Development Board to zestaw uruchomieniowy dla układu FPGA XC7A32T firmy Xilinix. Bogate wyposażenie dodatkowe, m.in.: 256 MB pamięci DDR3L, interfejs Ethernet 10/100Mb, konwerter USB - UART. 410-319
Brak towaru
Igła dozownicza zagięta do precyzyjnej aplikacji kleju, fluxu o średnicy wewnętrznej 0,26mm i średnicy zewnętrznej 0,5144mm
Brak towaru
Brak towaru
1.3 megapixel Digital Camera Module, for STM32F4DISCOVERY, STM, RoHS
Brak towaru
Brak towaru
Brak towaru
Kabel SATA do dysku twardego przeznaczony dla Banana Pi. Kabel zawiera linie zasilające.
Brak towaru
Wyświetlacz graficzny 128x64, 80x54mm, Backlight (yellow-green), Typ: COG, STN 3.3V ST7565R
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Tomasz Starecki
Brak towaru
Mikrokontroler z rodziny M68HC08. 24576B Flash, 768B RAM, I2C, SCI, SPI, sterownik LCD, obudowa QFP80.
Brak towaru
Rechargeable NiMH Battery Pack: 6.0 V, 200 mAh, 3+2 1/3-AAA Cells, JR Connector