- Out-of-Stock
This is a rechargeable 6.0 V NiMH battery pack with a capacity of 200 mAh. The pack consists of five 1/3-size AAA cells in two rows and a 4" lead terminated by a “JR”-style connector.
![]() |
This battery pack comes with 4" leads terminated by a 3-pin JR-style female connector (only two of the pins are used). The connector is the same as what is found on the most servos and has a 0.1" spacing, so it fits nicely with 0.1" male headers and can plug directly into most RC receivers, servo extension cables, and servo switch harnesses, and custom cables made with JR male connectors or Futaba J male connectors. Note, however, that this style of connector is often referred to as “male” in the RC hobby industry, so please use the picture on the right to clear up any potential confusion.
Our rechargeable NiMH battery packs give you variety of options for powering your robot or electronics project. The battery packs use 1.2 V cells and are available in several capacities:
![]() |
| Cell Type | Capacity (mAh) |
|---|---|
| AA | 2200 |
| AAA | 900 |
| 2/3 AAA | 350 |
| 1/3 AAA | 200 |
The picture to the right shows the relative sizes of our NiMH battery packs. These packs are well-suited for powering small robots, and the smaller (1/3- or 2/3-AAA) battery packs make great power sources for miniature robots, such as those that might be based on our Baby Orangutan robot controller.
|
|
Battery pack color may differ from what is shown in the main product picture.
Note: The battery voltages listed in the product descriptions are based on the 1.2 V nominal voltage of the NiMH cells from which the packs are made. The actual voltage will depend on how charged the batteries are. A fully charged NiMH cell will deliver almost 1.5 V, so, for example, a “6V”, 5-cell pack can measure over 7 volts after being charged, and it can fall well below 5 volts when the pack is drained. You will need to charge these battery packs before you first use them. The iMAX-B6AC battery charger works well with these battery packs.
Manufacturer
Responsible person
No product available!
Ready-to-use development platform designed around the Zynq-7000 All Programmable System-on-Chip (AP SoC) from Xilinx. The Zynq-7000 architecture tightly integrates a dual-core, 650 MHz ARM Cortex-A9 processor with Xilinx 7-series Field Programmable Gate Array (FPGA) logic. Digilent 410-346-20
No product available!
24-channel portable logic analyzer with 16-channel digital waveform generator. Digilent 410-338
No product available!
Banana Pi M2+ is another ARM SoC powered development board that offers great computing performance in an ultra portable form factor. It is a 65mm square with Allwinner H3 Quad-core A7 SoC and 1GB DDR3 RAM
No product available!
Laboratory power supply KORAD KA6005D 0..60 V, 0..5 A, memory 5 power profiles
No product available!
Banana Pi camera module for Banana Pi M3, includes CMOS sensor module: OV5640 (5M Pixel)
No product available!
Printed circuit board and programmed AA / AAA cell capacity tester. AVT3169 A +
No product available!
AVT kit for self-assembly of tester capacity AA / AAA cells. AVT3169 B
No product available!
Assembled cell capacitor AA / AAA. AVT3169 B
No product available!
Printed circuit board for water level indicator. AVT1949 A
No product available!
AVT kit for self-assembly of the water level indicator. AVT1949 B
No product available!
No product available!
AVT kit for self-assembly of 230V AC delay switch. AVT1950 B
No product available!
No product available!
A circuit board for an android driver with FT311D. AVT5575 A
No product available!
AVT kit for self-assembly of an android driver with FT311D. AVT5575 B
No product available!