- Obecnie brak na stanie
67:1 Metal Gearmotor 37Dx54L mm
This 2.13" x 1.45" x 1.45" gearmotor is a powerful brushed DC motor with 67:1 metal gearbox intended for operation at 12 V. These units have a 0.61"-long, 6 mm-diameter D-shaped output shaft. This gearmotor is also available with an integrated encoder.
Key specs at 12 V: 150 RPM and 300 mA free-run, 200 oz-in (14 kg-cm) and 5 A stall.
This powerful brushed DC gearmotor is available in six different gear ratios. A version with an integrated encoder is also available.
| Gear Ratio | Speed @ 12V | Stall Torque @ 12V | Stall Current @ 12V | ![]() With Encoder | ![]() Without Encoder |
|---|---|---|---|---|---|
| 19:1 | 500 RPM | 84 oz-in | 5 A | 37Dx52L mm | 37Dx52L mm |
| 29:1 | 350 RPM | 110 oz-in | 5 A | 37Dx52L mm | 37Dx52L mm |
| 50:1 | 200 RPM | 170 oz-in | 5 A | 37Dx54L mm | 37Dx54L mm |
| 67:1 | 150 RPM | 200 oz-in | 5 A | 37Dx54L mm | 37Dx54L mm |
| 100:1 | 100 RPM | 220 oz-in | 5 A | 37Dx57L mm | 37Dx57L mm |
| 131:1 | 80 RPM | 250 oz-in | 5 A | 37Dx57L mm | 37Dx57L mm |
These motors are intended for use at 12 V, though the motor can begin rotating at voltages as low as 1 V.
The face plate has six mounting holes evenly spaced around the outer edge threaded for M3 screws. These mounting holes form a regular hexagon and the centers of neighboring holes are 15.5 mm apart. You can use our custom 37D metal gearmotor bracket (shown in the left picture below) to mount the gearmotor to your project via these mounting holes and the screws that come with the bracket.
|
|
Please note that unlike our smaller metal gearmotors, these 37D mm gearmotors have output shafts with a diameter of 6 mm. The Pololu universal aluminum mounting hub for 6mm shafts can be used to mount our larger Pololu wheels (80mm- and 90mm-diameter) or custom wheels and mechanisms to the gearmotor’s output shaft (see the right picture above).
The picture below shows the dimensions (in mm) of the 37D mm line of gearmotors. The value of X is 22 mm for the 19:1 37Dx52L mm and 29:1 37Dx52L mm versions, 24 mm for the 50:1 37Dx54L mm and 67:1 37Dx54L mm versions, and 26.5 mm for the 100:1 37Dx57L mm and 131:1 37Dx57L mm versions.
![]() |
| 37D mm metal gearmotor dimensions (units in mm). |
|---|
Warning: Do not screw too far into the mounting holes as the screws can hit the gears. We recommend screwing no further than 3mm (1/8") into the screw hole.
The operational specs listed in the table below were measured at 6 V. At 12 V, the no-load RPM, stall current, and stall torque will all be approximately twice their 6V values. To see the motor specs for 12V operation, please see the short description at the top of this page or this product’s specification tab.
![]() |
| 37D mm metal gearmotor next to a micro metal gearmotor for size comparison. |
|---|
We offer a wide selection of metal gearmotors that offer different combinations of speed and torque. Our metal gearmotor comparison table can help you find the motor that best meets your project’s requirements.
![]() |
| Some of the Pololu metal gearmotors. |
|---|
![]() |
Pololu 37D mm Metal Gearmotor Bracket Pair |
![]() |
Pololu Universal Aluminum Mounting Hub for 6mm Shaft Pair, 4-40 Holes |
![]() |
Pololu Simple Motor Controller 18v7 (Fully Assembled) |
Cechy
Producent
Osoba odpowiedzialna
Moduł kamery przeznaczony dla płyt deweloperskich RP2040 . Wykorzystuje sensor Himax HM01B0 pozwalający osiągnąć doskonałą wydajność przy słabym oświetleniu. ArduCAM B328
Brak towaru
Moduł z sensorem OV5647 współpracujący z wszystkimi wersjami Raspberry Pi. Wykorzystuje wbudowany ruchomy filtr IR-CUT, włączany i wyłączany automatycznie w zależności od warunków oświetleniowych. ArduCAM B003507
Brak towaru
Zestaw 4 płyt montażowych dla Raspberry Pi 4B kompatybilnych z 19-calowym uchwytem do montażu w szafie 3U. Uchwyt znajdujący się na 3. zdjęciu, nie znajduje się w zestawie i należy zakupić go osobno. ArduCAM U6131
Brak towaru
Moduł kamery z sensorem IMX477 HQ przeznaczony dla Raspberry Pi Compute Module (CM3, CM3+, CM4). Wyposażony w obiektyw z mocowaniem M12 o kącie widzenia 75°. ArduCAM B0271
Brak towaru
Kamera z interfejsem USB o rozdzielczości 8 MP. Wyposażona w sensor Sony CMOS IMX179 oraz szerokokątny obiektyw o kącie widzenia 105°. ArduCAM UB0229
Brak towaru
Moduł kamery 1 MPx z sensorem OV9281 współpracujący z wszystkimi wersjami Raspberry Pi. Wyposażony w migawkę i filtr IR, charakteryzuje się dobrą czułością. ArduCAM B0225
Brak towaru
Moduł kamery 2 MPx z sensorem OV2311 współpracujący z Raspberry Pi. Wyposażony w migawkę i mocowanie obiektywów M12. ArduCAM B0219
Brak towaru
Zestaw kamery z sensorem IMX219 8 MPx, pozwala na obracanie kamerą, sterowanie kątem nachylenia oraz zoomem. Współpracuje z Raspberry Pi. W zestawie obrotowa podstawa. ArduCAM B0167B8
Brak towaru
Moduł kamery 2 MPx z sensorem OG02B10 współpracujący z wszystkimi wersjami Raspberry Pi. Wyposażony w migawkę, charakteryzuje się dobrą czułością. ArduCAM B0199
Brak towaru
Moduł kamery 8 MPx z sensorem IMX219 i obiektywem o kącie widzenia 75°. Przeznaczona do użytku jako element zamienny na płytce RPI Camera Board V2. ArduCAM B0188
Brak towaru
Moduł z kamerą 8 Mpx IMX219 i obiektywem o kącie widzenia 75°. Przeznaczony dla Nvidia Jetson Nano oraz Raspberry Pi CM. ArduCAM B0187
Brak towaru
Zestaw z dwiema kamerami IMX219 o rozdzielczości 8 MP oraz modułem rozszerzeń dla Raspberry Pi, który pozwala na jednoczesne podłączenie dwóch kamer. ArduCAM B0350
Brak towaru
Moduł kamery 2 MPx OG02B10 współpracujący z Raspberry Pi. W zestawie adapter. ArduCAM B0348
Brak towaru
Moduł kamery z sensorem IMX219 o rozdzielczości 8 MP przeznaczony dla NVIDIA Jetson Nano/Xavier oraz Raspberry Pi Compute Module. ArduCAM B0342
Brak towaru
Moduł kamery 2 MPx z sensorem OV2311 współpracujący z NVIDIA Jetson Nano. Wyposażony w migawkę i mocowanie obiektywów M9. W zestawie akrylowa obudowa. ArduCAM B0220
Brak towaru
Zestaw zawierający moduł z dwiema kamerami z sensorem IMX219 o rozdzielczości 8 MP oraz moduł rozszerzeń dla NVIDIA Jetson Nano. ArduCAM B0217J8
Brak towaru
67:1 Metal Gearmotor 37Dx54L mm