![Pololu 1392 - Pololu Jrk 21v3 USB Motor Controller with Feedback Pololu 1392 - Pololu Jrk 21v3 USB Motor Controller with Feedback](https://kamami.pl/8473-large_default/pololu-1392-pololu-jrk-21v3-usb-motor-controller-with-feedback.jpg)
![Pololu 1392 - Pololu Jrk 21v3 USB Motor Controller with Feedback Pololu 1392 - Pololu Jrk 21v3 USB Motor Controller with Feedback](https://kamami.pl/8473-large_default/pololu-1392-pololu-jrk-21v3-usb-motor-controller-with-feedback.jpg)
302,80 zł Netto
Pololu Jrk 21v3 USB Motor Controller with Feedback
darmowa wysyłka na terenie Polski dla wszystkich zamówień powyżej 500 PLN
Jeśli Twoja wpłata zostanie zaksięgowana na naszym koncie do godz. 11:00
Każdy konsument może zwrócić zakupiony towar w ciągu 14 dni bez zbędnych pytań
Pololu Jrk 21v3 USB Motor Controller with Feedback
The jrk 21v3 motor controller is a highly configurable brushed DC motor controller that supports four interface modes: USB, logic-level serial, analog voltage, and hobby radio control (RC). The controller can be used with feedback for closed-loop speed or position control, or it can be used without feedback as an open-loop speed control. The continuous output current is approximately 3 A in the recommended operating range of 8–28 V, with derated performance down to 5 V and transient protection to 40 V. The board ships with connectors included but not soldered in, allowing for custom installations.
![]() |
The jrk 21v3 is a versatile, general-purpose motor controller that supports a variety of interfaces, including USB. The broad operating range from 5 V to 28 V and continuous output current of 3 A (5 A peak) allow this board to control most small DC brushed motors. Analog voltage and tachometer (frequency) feedback options allow quick implementation of closed-loop servo systems, and a free configuration utility (for Windows 7, Vista, or Windows XP) allows easy calibration and configuration through the USB port.
Key improvements over competing products and earlier Pololu motor controllers with feedback include:
Note: A USB A to mini-B cable (not included) is required to connect this controller to a computer.
![]() |
![]() |
![]() |
Motor channels: | 1 |
---|---|
Operating voltage: | 5 – 28 V |
Continuous output current: | 3 A |
Peak output current: | 5 A |
Auto-detect baud rate range: | 300 – 115,200 bps |
Available fixed baud rates: | 300 – 115,200 bps |
Available PWM frequencies: | 20 kHz, 5 kHz |
Reverse voltage protection?: | Yes |
USB connector style: | USB Mini-B |
The jrk 21v3 is the smaller of two jrk motor controllers. For a higher-power version, see the jrk 12v12.
|
|
The jrk 21v3 is available in two versions: “fully assembled” with terminal blocks and 0.1" male header pins pre-installed (left picture above), and connector-free (right picture above). The connector-free version includes a 14×1 straight 0.100" breakaway male header strip and two 3.5mm, 2-pin terminal blocks, but these parts are not soldered to the board, which allows for custom installations.
The three mounting holes are intended for use with #2 screws (not included).
|
|
||||
|
|
![]() |
Micro Maestro 6-Channel USB Servo Controller (Assembled) |
![]() |
Pololu Qik 2s9v1 Dual Serial Motor Controller |
![]() |
Pololu Jrk 12v12 USB Motor Controller with Feedback |
Sterownik silnika prądu stałego (DC) o napięciu pracy 6-34V i maksymalnym prądzie ciągłym 30A. Posiada możliwość łatwej realizacji pętli sprzężenia zwrotnego oraz liczne systemy bezpieczeństwa. Pololu 3290
Podwójny sterownik silników pozwalający na sterowanie dwóch silników DC napięciem 0-11V i prądem ciągłym 1,2A na kanał. Pololu 2135
Moduł rozszerzeń przeznaczony do współpracy z płytką edukacyjną micro:bit. Może sterować 3 serwomechanizmami i 2 silnikami prądu stałego. Waveshare Motor Driver for micro:bit
Pololu High-Power Motor Driver 18v15
Brak towaru
Jednokanałowy sterownik silników DC z interfejsem I2C. Jest zasilany napięciem od 4,5 V do 48 V i może dostarczyć prąd o natężeniu do 2,2 A. Płytka ze złączami do montażu. Pololu 5061
Brak towaru
Pololu High-Power Motor Driver 18v25 CS
RoboClaw 2x60AHV Motor Controller (V7C) to dwukanałowy sterownik silników prądu stałego (DC), napięcie pracy: od 10,5 do 60V, maksymalny prąd ciągły: 60A, możliwość łatwej realizacji pętli sprzężenia zwrotnego z regulatorem PID, systemy bezpieczeństwa. Pololu 3583
Brak towaru
Moduł ze sterownikiem silnika krokowego oparty na układzie DRV8825. pozwala na zasilanie silnika bipolarnego prądem do 1,5 A na fazę, bez użycia radiatora. Układ może być zasilany napięciem do 45 V. Pololu 2987
Niewielka płytka z sterownikiem silnika szczotkowego MAX14870 działającym w napięciach od 4,5V do 36V i prądzie ciągłym 1,7 A (2,5 A chwilowym). Pololu 2961
Pololu Simple High-Power Motor Controller 24v23
Brak towaru
Brak towaru
Sterownik silników DC, który pozwala na kontrolowanie ruchu dwóch napędów za pomocą interfejsu I2C. Płytka z przylutowanymi złączami. Pololu 5054
Brak towaru
RPi Motor Driver Board to sterownik przeznaczony dla dwóch silników DC lub jednego silnika krokowego. Sterownik jest przystosowany do dołączenia do komputerów serii Raspberry Pi A+, B+, 2 B i 3 B
RoboClaw 2x160A Motor Controller to dwukanałowy sterownik silników prądu stałego (DC), napięcie pracy: 10,5..60V, maksymalny prąd ciągły: 120A, możliwość łatwej realizacji pętli sprzężenia zwrotnego z regulatorem PID, systemy bezpieczeństwa. Pololu 3582
Brak towaru
2x1.2A DC Motor Driver to podwójny sterownik silników DC zasilanych napięciem 2,5-12V o maksymalnym poborze prądu 1,2A (3,2A w szczycie) na kanał. DFRobot DRI0044
DRV8834 Low-Voltage Stepper Motor Driver Carrier
Pololu Jrk 21v3 USB Motor Controller with Feedback