- Obecnie brak na stanie
![Pololu 1162 - 29:1 Metal Gearmotor 20Dx41L mm Pololu 1162 - 29:1 Metal Gearmotor 20Dx41L mm](https://kamami.pl/8059-large_default/pololu-1162-291-metal-gearmotor-20dx41l-mm.jpg)
29:1 Metal Gearmotor 20Dx41L mm
darmowa wysyłka na terenie Polski dla wszystkich zamówień powyżej 500 PLN
Jeśli Twoja wpłata zostanie zaksięgowana na naszym koncie do godz. 11:00
Każdy konsument może zwrócić zakupiony towar w ciągu 14 dni bez zbędnych pytań
29:1 Metal Gearmotor 20Dx41L mm
This 1.46" x 0.79" x 0.79" gearmotor is a brushed DC motor with 29:1 metal gearbox that has the power to deliver both speed and torque. These units have a 0.276"-long, 4 mm-diameter D-shaped output shaft. This gearmotor is a replacement for the now-discontinued 25:1 version.
Key specs at 6 V: 440 RPM and 250 mA free-run, 25 oz-in (1.8 kg-cm) and 3.3 A stall.
The 20D mm line of brushed DC gearmotors are available in three different gear ratios, all of which have the same dimensions except for the length of the gearbox. The gearmotor face plate has two mounting holes threaded for M2.5 screws, and you can use our custom-designed 20D mm metal gearmotor bracket (shown in the left picture below) to mount the gearmotor to your project via these mounting holes and the screws that come with the bracket.
|
|
This gearmotor has an output shaft with a diameter of 4 m; the Pololu universal aluminum mounting hub for 4mm shafts can be used to mount our larger Pololu wheels (60mm-, 70mm-, 80mm-, and 90mm-diameter) or custom wheels and mechanisms to the gearmotor’s output shaft (see the right picture above). The gearbox’s output shaft also works directly with the 120mm-diameter Wild Thumper wheels, as shown below.
![]() |
Dagu Wild Thumper wheel 120×60mm (metallic red) with Pololu 20D mm metal gearmotor. |
---|
The picture below shows the dimensions (in mm) of the 20D mm line of gearmotors. The value of L
depends on the gear ratio of the gearbox: 29:1 is 15.7 mm, 73:1 is 17.2 mm, and 154:1 is 18.6 mm.
![]() |
20D mm metal gearmotor dimensions (units in mm, L=18.5mm). |
---|
Note: These motors are intended for use at 6 V. In general, these kinds of motors can run at voltages above and below this nominal voltage, so they should comfortably operate in the 3 – 9 V range. Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.
Note: The older, discontinued 25:1 and 67:1 versions of this gearmotor now had a different mounting hole spacing and work with a slightly different bracket. This bracket is not compatible with the 29:1, 73:1, and 154:1 20D mm gearmotors we currently offer.
We offer a wide selection of metal gearmotors that offer different combinations of speed and torque. Our metal gearmotor comparison table can help you find the motor that best meets your project’s requirements.
![]() |
Some of the Pololu metal gearmotors. |
---|
![]() |
Pololu 20D mm Metal Gearmotor Bracket Pair |
![]() |
Pololu Universal Aluminum Mounting Hub for 4mm Shaft Pair, 4-40 Holes |
![]() |
50:1 Micro Metal Gearmotor HP |
Brak towaru
Zestaw AVT do samodzielnego montażu zdalnego włącznika radiowego. AVT5590 B
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Płytka uruchomieniowa z mikrokontrolerem SAMD21 (ARM Cortex® M0+), 8 linii I/O, 12 kanałów PWM. Płytka wyposażona jest w moduł ATSAMD21 oraz U-blox SARA-U201 umożliwiające implementację komunikacji w sieciach GSM. Arduino MKR GSM 1400 ABX00018
Brak towaru
Brak towaru
Akumulator Li-Po 3,7V/320mAh, zabeczpieczenie PCM, konektor+gniazdo 2,5 JST-RCY (BEC), 2 piny, długość przewodu 150mm, wymiary: 40 x 30 x 3mm, waga: 9g
Brak towaru
ABC016004A23-BLW-R - Wyświetlacz LCD 4x16, 87x60mm, podświetlanie LED (white), NEGATIVE BLUE, STN, rozszerzony zakres temperatury, RoHS
Brak towaru
Brak towaru
Brak towaru
Brak towaru
29:1 Metal Gearmotor 20Dx41L mm