- Out-of-Stock

This 1.46" x 0.79" x 0.79" gearmotor is a brushed DC motor with 29:1 metal gearbox that has the power to deliver both speed and torque. These units have a 0.276"-long, 4 mm-diameter D-shaped output shaft. This gearmotor is a replacement for the now-discontinued 25:1 version.
Key specs at 6 V: 440 RPM and 250 mA free-run, 25 oz-in (1.8 kg-cm) and 3.3 A stall.
The 20D mm line of brushed DC gearmotors are available in three different gear ratios, all of which have the same dimensions except for the length of the gearbox. The gearmotor face plate has two mounting holes threaded for M2.5 screws, and you can use our custom-designed 20D mm metal gearmotor bracket (shown in the left picture below) to mount the gearmotor to your project via these mounting holes and the screws that come with the bracket.
|
|
This gearmotor has an output shaft with a diameter of 4 m; the Pololu universal aluminum mounting hub for 4mm shafts can be used to mount our larger Pololu wheels (60mm-, 70mm-, 80mm-, and 90mm-diameter) or custom wheels and mechanisms to the gearmotor’s output shaft (see the right picture above). The gearbox’s output shaft also works directly with the 120mm-diameter Wild Thumper wheels, as shown below.
![]() |
Dagu Wild Thumper wheel 120×60mm (metallic red) with Pololu 20D mm metal gearmotor. |
---|
The picture below shows the dimensions (in mm) of the 20D mm line of gearmotors. The value of L
depends on the gear ratio of the gearbox: 29:1 is 15.7 mm, 73:1 is 17.2 mm, and 154:1 is 18.6 mm.
![]() |
20D mm metal gearmotor dimensions (units in mm, L=18.5mm). |
---|
Note: These motors are intended for use at 6 V. In general, these kinds of motors can run at voltages above and below this nominal voltage, so they should comfortably operate in the 3 – 9 V range. Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.
Note: The older, discontinued 25:1 and 67:1 versions of this gearmotor now had a different mounting hole spacing and work with a slightly different bracket. This bracket is not compatible with the 29:1, 73:1, and 154:1 20D mm gearmotors we currently offer.
We offer a wide selection of metal gearmotors that offer different combinations of speed and torque. Our metal gearmotor comparison table can help you find the motor that best meets your project’s requirements.
![]() |
Some of the Pololu metal gearmotors. |
---|
![]() |
Pololu 20D mm Metal Gearmotor Bracket Pair |
![]() |
Pololu Universal Aluminum Mounting Hub for 4mm Shaft Pair, 4-40 Holes |
![]() |
50:1 Micro Metal Gearmotor HP |
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
MP3 player module controlled by the I2C interface. It is based on a class D amplifier with a power of 1.4 W. The board has a 3.5 mm headphone output and an 8 Ω speaker connector. Audio files are saved on the microSD card. SparkFun DEV-15165
No product available!
GreenBlue preparation, allows concentrated blowing to inaccessible places, removes dust from various elements, environmentally friendly agent
No product available!
No product available!
group work
No product available!
No product available!
No product available!
No product available!
High voltage differential probe. It is characterized by good measurement parameters: with a 100 MHz band and an operating voltage up to 5600 V. The probe has two attenuation factors: 200X and 2000X. Micsig DP20003
No product available!
No product available!
No product available!
No product available!
Set of 6 screwdrivers for electronics (flat 4 pcs, cross-brace 2 pcs) from Velleman. Length 130mm
No product available!
No product available!
No product available!
No product available!
HK Hobbyking 2~6S Lipo to USB Charging Adapter and Cell Checker (22320)
No product available!