- Obecnie brak na stanie
![Pololu 1608 - Parallax ColorPAL Pololu 1608 - Parallax ColorPAL](https://kamami.pl/8878-large_default/pololu-1608-parallax-colorpal.jpg)
darmowa wysyłka na terenie Polski dla wszystkich zamówień powyżej 500 PLN
Jeśli Twoja wpłata zostanie zaksięgowana na naszym koncie do godz. 11:00
Każdy konsument może zwrócić zakupiony towar w ciągu 14 dni bez zbędnych pytań
The Parallax ColorPAL combines an RGB LED, a light sensor, and a microcontroller to make a color sensor that can also be used as an ambient light detector and a color generator. Readings are reported via a 1-wire asynchronous serial interface.
![]() |
ColorPAL side view. |
---|
The ColorPAL from Parallax is a miniature color and light sensor that can double as a color generator with its RGB LED. When sensing color, the ColorPAL uses its LED to illuminate a sample one color component at a time while measuring the light reflected back with a broad-spectrum light-to-voltage converter. The amount of light reflected from the sample under illumination from each red, green, and blue LED can be used to determine the sample’s color. For the ColorPAL to detect the color of a subject, the subject must be reflective and non-fluorescent. The color of objects that emit light (e.g. LEDs) cannot be detected.
Communication with the ColorPAL takes place using serial I/O, transmitting and receiving at between 2400 and 7200 baud, using a non-inverted, open-drain protocol. The ColorPAL includes a pull-up resistor to Vdd, so you do not need to apply one externally. Because of the open-drain protocol, the pin used to communicate with the ColorPAL should always be configured as an input, except when being driven low. Also, when starting up, you should wait for this pin to be pulled high by the ColorPAL before trying to send it any commands. Please see the user’s manual (297k pdf) for more information.
![]() |
Sharp GP2Y0A02YK0F Analog Distance Sensor 20-150cm |
![]() |
Sharp GP2Y0A21YK0F Analog Distance Sensor 10-80cm |
![]() |
MLX90614ESF-AAA Infrared Temperature Sensor 90° FOV |
Filament firmy ROSA3D wykonany z wysokiej jakości granulatu PLA z niewielkim dodatkiem włókien węglowych. Na szpuli nawinięte jest 0,5 kg filamentu o średnicy 1,75 mm. ROSA3D PLA CarbonLook
Brak towaru
Brak towaru
INTERFEJS WYŚWIETLACZY GRAFICZNYCH LCD - PŁYTKA DRUKOWANA I ZAPROGRAMOWANY UKŁAD
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Zestaw AVT do samodzielnego montażu uniwersalnego modułu zasilającego 15V. AVT1895/15 B
Brak towaru
Brak towaru
Brak towaru
Moduł GY-GPS6MV1 to płytka zawierająca układ odbiornika GPS NEO-6M firmy U-blox. Na płytce znajduje się również m.in. bateria podtrzymująca RTC, złącze do anteny (U.FL), stabilizator napięcia i wyjścia sygnałów UART
Brak towaru
Brak towaru
Płytka PCB i zaprogramowany układ do dużego termometru XXL, mierzącego temperaturę w zakresie od -55... +125°C. AVT1790A+
Brak towaru
Capacitive proximity switch with auto-calibration, large voltage operating range and very low power consumption, SOIC8, NXP, RoHS
Brak towaru
Obudowa do Orange Pi Plus jest przezroczysta, na zatrzaski. Montaż nie wymaga użycia kleju. Obudowa jest wykonana z wysokiej jakości tworzywa sztucznego. Wszystkie otwory wykonane w obudowie pozwalają na łatwy dostęp do każdego gniazda wbudowanego w Orange Pi Plus
Brak towaru
Brak towaru
Brak towaru