- Obecnie brak na stanie
JR Connector Pack, Male
This pack contains everything you need to add up to three male JR connectors — the connectors that mate with those commonly found on generic RC servos — to custom cables. You can use a crimping tool to attach the included pins to your own 22–26 AWG wires. This pack contains enough housings and crimp pins (including 3 spare pins) for 3 male connectors. The crimp pins have gold-flashed male contacts.
This JR connector has a 0.1" pin spacing and mates with the female JR connectors commonly found on RC servos. The corresponding female JR connector has two corners that are slightly beveled, which makes it difficult (but not impossible) to incorrectly plug them into this connector. This pack contains three female JR housings, three male JR shrouds, and twelve gold-flashed crimp pins, which is enough for three complete male connectors and three spare pins. The crimp pins are designed for 22–26 AWG wires, and we sell a crimping tool that works well with them. You can use these connectors to make your own custom servo cables or servo extension cables.
To assemble the connectors, push the crimped male pins into the female housing until you hear them lock into place (the prongs will protrude out of the connector sockets), and then slide that assembly into the shroud. If you look inside the shroud, you will see a raised bump closer to one of the two openings; this is the opening into which you should plug the connector subassembly, and you should plug the assembly in so that the side of the female housing with the crimp pin latches faces the side of the shroud with the bump. If you have done things right, you will hear a snap when you push the female housing into the shroud, and it will lock in place. Note that If you want a cable that you can plug into a breadboard rather than a female JR connector, you can leave the shroud off.
We also sell Futaba J connectors, which are very similar but have an additional polarizing tab/slot, and we carry an variety of premade servo extension and splitter cables.
Note: these connectors are commonly referred to as “female” in the RC hobby industry, so please look carefully at the pictures of male JR connectors below to make sure they are what you want.
|
|
![]() |
JR Connector Pack, Female |
![]() |
Crimping Tool: 0.1-1.0 mmÂ? Capacity, 16-28 AWG |
![]() |
Female Crimp Pins for 0.1" Housings 100-Pack |
Producent BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Osoba odpowiedzialna BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Brak towaru
Moduł MCU łączący technologie Wi-Fi i Bluetooth (BLE), który jest przeznaczony do szerokiej gamy aplikacji, od sieci czujników o niskiej mocy do najbardziej wymagających zadań, takich jak kodowanie głosu, przesyłanie strumieniowe muzyki i dekodowanie MP3. Espressif ESP32-WROOM-32D 32MBit
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Igła dozownicza zagięta do precyzyjnej aplikacji kleju, fluxu o średnicy wewnętrznej 0,603mm i średnicy zewnętrznej 0,9081mm
Brak towaru
Złącze terminalowe ARK sprężynowe 8-pinowe o rastrze 3,5 mm, nierozłączalne.
Brak towaru
P-NUCLEO-IOM01M1 to zestaw STM32 Nucleo składający się z płytek STEVAL-IOM001V1 (fizyczna warstwa stacji IO-Link) oraz NUCLEO-F446RE (pełniący funkcję stosu IO-Link). P-NUCLEO-IOM01M1
Brak towaru
Dotykowy wyświetlacz LCD o rozdzielczości 160x128 pikseli, kontroler wyświetlacza LCD160CR (I2C lub UART i SPI). Adafruit 3498
Brak towaru
Brak towaru
Brak towaru
Przewód głośnikowy, dwużyłowy o przekroju 0,75 mm2, czarno-czerwony, izolacja wykonana z PVC. Cena za metr bieżący. TASKER TSK52
Brak towaru
Brak towaru
Uniwersalny multimetr do zastosowań w diagnostyce samochodowej. Pozwala zmierzyć napięcie stałe i przemienne, prąd stały i przemienny, rezystancję, temperaturę i pojemność oraz częstotliwość. Umożliwia pomiar parametrów charakterystycznych dla branży automotive, takich jak RPM czy DWELL. Uni-T UT109
Brak towaru
Płytka ewaluacyjna WIFI501 z modułem WIFI232-B
Brak towaru
CAPE dla komputera Beaglebone Black umożliwiający dołączenie shieldów zgodnych Arduino UNO i Arduino Leonardo
Brak towaru
JR Connector Pack, Male