List of products by brand DFRobot

Module with an IR transmitter operating at a frequency of 38kHz. The module is supplied with the voltage from 3 to 5V. FRobot DFR0095

LoRa radio module with 433 MHz operating frequency. Communication takes place via the UART serial interface. It is supplied with the voltage in the range from 3.4 to 5.5 V. DFRobot TEL0116

Gravity: Digital Peristaltic Pump is a peristaltic pump with a controller and a connector compatible with modeling servos. The set is powered by 5 ... 6 V. DFRobot DFR0523

The expansion board is designed for DFRduino M0 or Bluno M0 sets. The board has 31 GPIO pins (including 6 PWM and 6 ADC inputs), UART, I2C and SPI interfaces. The pins are color coded according to the Gravity standard. DFRobot DFR0412

7" LCD display with capacitive touch screen. The display is equipped with HDMI interface for image display and USB for touch screen. It has a resolution of 1024x600 pixels. DFRobot DFR0506

LM35 analog temperature sensor module for Arduino. DFRobot DFR0023

Audio Analyzer is a module with sound analyzer based on the MSGEQ7 system. It divides the sound into seven frequency bands, and then allows you to read the peak levels of each band. It allows you to measure the sound in the following frequencies: 63Hz, 160Hz, 400Hz, 1kHz, 2.5kHz, 6.25kHz and 16kHz. DFRobot DFR0126

DRV8825 Stepper Motor Driver Module for Arduino. It allows you to control two drives, equipped with an XBee connector. DFRobot DRI0023

IoT module with ATmega328P and BLE4.1 microcontroller. Compatible with the Bluno series, it can be programmed in the Arduino IDE. DFRobot DFR0492

SCD41 CO2, temperature and humidity sensor module. Equipped with a Gravity connector, it communicates via an I2C interface. DFRobot SEN0536

Expansion board for micro:bit modules with connectors compatible with Boson and Gravity sets. DFRobot DFR0521

Temperature and humidity sensor SHT20 closed in a waterproof housing. Communication via the I2C interface. DFRobot SEN0227

Development kit with nRF51822 microcontroller and GSM/GPRS MT6260 chip. Dedicated to the construction of "wearable" devices and IoT devices. DFRobot DFR0383

Gravity: Analog Signal Isolator is a module that allows to isolate sensors in the system and eliminate mutual interference of sensors powered by 5V. DFRobot DFR0504

The MiniQ 2WD Robot Kit v2.0 chassis has a built-in driver compatible with the Arduino Leonardo plate. The chassis has been equipped with reflective sensors, a compass and obstacle sensors. Thanks to them, it is possible to create a robot following a line (linefollower) or controlled by an IR remote (which is included in the set). DFRobot ROB0081

Motor with a diameter of 25 mm and a length of 71 mm, with a metal gearbox of 75:1, operating voltage of 6 V, current consumption from 0.13 A to 3 A, speed 100 RPM, maximum torque 6.5 kg*cm and magnetic encoder. DFRobot FIT0522

Advanced expansion board for Arduino. It has support for mini-SIM cards and NB-IoT cards. Thanks to the GNSS module (Global Navigation Satellite System), it supports GPS, GLONASS, Galileo, QZSS and BeiDou GPS navigation systems. The module is powered by 7-12V voltage. DFRobot DFR0572

2x16 character LCD display. It can display the font in any color from the RGB palette. Communication via the I2C interface. The module has a lead compliant with the Gravity standard. DFRobot DFR0554

Clock & Timer Development Tools Gravity I2C SD2405 RTC. DFR0469

A magnetic stirrer that uses a rotating magnetic field to very quickly spin an element immersed in a liquid, which leads to its mixing. It will be used in laboratories. DFRobot FIT0537