- Obecnie brak na stanie

ISD1932 Voice Recorder Carrier
This breakout board from Sparkfun is a carrier for the ISD1932 multiple-message record/playback IC. It can record up to 64 seconds of voice messages with two different recording trigger modes. The chip has a flexible supply voltage of 2.4 to 5 VDC and breaks out all of the ISD1932’s pins to 0.1"-spaced headers.
![]() |
ISD1932 voice recorder carrier top view. |
---|
![]() |
ISD1932 voice recorder carrier bottom view. |
---|
This breakout board from SparkFun is a carrier for the ISD1932, a multiple-message record/playback device. This single chip can record up to 64 seconds of voice messages. Microphone inputs and speaker outputs are all handled by the ISD1932. Since this board is a carrier for the ISD1932, careful reading of the datasheet (503k pdf) is recommended.
A switch is connected to allow selection between two of the ISD1932’s operating modes: address trigger or direct trigger. You need to cycle the power after flipping the mode switch to change the mode. The board’s LED will illuminate when the device is recording.
An external resistor is necessary to select the sampling frequency, which in turn determines the recording duration. The duration can range from 21.3 s with a sampling frequency of 12 kHz to 64 s with a sampling frequency of 4 kHz.
The board breaks out all pins of the ISD1932 to 0.1" spaced headers that work with our 0.1" male headers and allow the board to be used with standard breadboards and perfboards. The boards’s headers also work with our 0.1" female headers.
![]() |
Electret Microphone Breakout Board |
![]() |
50mm Speaker: 8 Ohm, 1 W |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x2-Pin 25-Pack |
Producent BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Osoba odpowiedzialna BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Polska sprzedaz@kamami.pl 22 767 36 20
Brak towaru
Filament firmy ROSA3D wykonany z wysokiej jakości granulatu PET-G. Na szpuli nawinięte jest 0,8 kg filamentu o średnicy 1,75 mm. ROSA3D PET-G Standard Light Green Transparent
Brak towaru
Kamera z sensorem CMOS OV2710 o rozdzielczości 1945x1109 px. Komunikuje się przez interfejs równoległy. ArduCAM U6034
Brak towaru
Oprogramowanie LabVIEW 2014 w wersji Home Bundle. LabView służy do wizualnego programowania, projektowania graficznych interfejsów użytkownika, umożliwia także tworzenie interakcji z narzędziami sprzętowymi. 6002-549-000
Brak towaru
Brak towaru
Brak towaru
Karta microSD z adapterem SD (16 GB, klasa 10) z wgranym oprogramowaniem NOOBS dla Raspberry Pi
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Niskoprądowy (low power) moduł Bluetooth z wbudowaną anteną. Moduł ma wtyczkę pasującą do popularnego gniazda 2x10 (2mm), stosowanego w modułach radiowych IEEE 802.15.4. Obsługuje profile SPP oraz HID. WRL-11600
Brak towaru
REJESTRATOR TEMPERATURY TLOG_2 - PŁYTKI DRUKOWANE I ZAPROGRAMOWANY UKŁAD - PŁYTKA DRUKOWANA I ZAPROGRAMOWANY UKŁAD
Brak towaru
Brak towaru
Brak towaru
Brak towaru
Moduł stabilizatora służy do stabilizowania napięcia wyjściowego na odpowiednim poziomie oraz filtrowania zakłóceń. Moduł może być zasilany napięciem do +16V, a napięcie wyjściowe wynosi +12V.
Brak towaru
ISD1932 Voice Recorder Carrier