- Obecnie brak na stanie
Pololu RC Switch with Digital Output
This tiny board converts hobby radio control pulses to digital on/off signals for use in RC switch and simple RC adapter applications. One output indicates the presence of a valid RC signal (10-100 Hz pulse rate, 0.5-2.5 ms pulse width), and the other output indicates whether the pulse width is above or below the 1.6 ms threshold (with ±0.1 ms hysteresis).
![]() |
The Pololu RC switch with digital output can be used with standard hobby radio control systems for radio control switch applications or simple interface applications. Example applications include converting extra RC receiver or servo controller outputs to simple high/low signals that can control LEDs or MOSFETs or relays and connecting RC systems to microcontroller projects that do not have the necessary resources for decoding the RC interface. Two outputs indicate the presence of a valid signal and whether the switch is on or off. This compact unit measures a mere 0.4" x 0.4" and weighs just 0.3 g (0.01 oz).
![]() |
The RC switch PCB has two sets of connections, one on each side. The side with three pins can connect directly to an RC receiver or servo controller; the side with four pins has the board power supply connections and two outputs. The outputs will be at the same levels as the VCC power connection, which can range from 2.0 V to 5.5 V. The RC signal input, IN, voltage can range from 0 to 7 V, and the threshold for a logic high is approximately 1 V. The VCC pin can be connected to the RC supply, VRC, by shorting across the appropriate pads on the back side of the PCB, allowing either the RC receiver to power the digital device or allowing the digital system to power the RC receiver (if the connection between the two power pins is not made, VRC can be left disconnected since it is not used by the RC switch board).
The board has two outputs, each of which is capable of sourcing or sinking 20 mA. The primary output, OUT, goes high (on) when a valid signal is detected and the pulse width is above the threshold of 1.6 ms. There is approximately ±0.1 ms of hysteresis on the threshold, meaning that the pulse width will have to get to approximately 1.7 ms before the output turns on, and once on, the signal will have to fall below 1.5 ms to turn off. A secondary output, GOOD, can be used to indicate the presence of a valid RC signal (10-100 Hz pulse rate, 0.5-2.5 ms pulse width).
An LED on the RC switch indicates the status of the RC signal (and outputs). When a valid RC signal is not detected (GOOD and OUT both low), the LED flashes with a duty cycle of approximately 50% (i.e. the LED is on for as long as it is off). When a valid signal is detected but the pulse width is below the threshold (GOOD high and OUT low), the LED flashes at a very low duty cycle (i.e. very short flashes). When a good signal is detected and the pulse width is above the threshold, both outputs are high and the LED turns on (no flashing).
A 7-pin 0.1" straight breakaway male header is included with the Pololu RC switch with digital output, which can be used to connect the RC switch to perfboards or breadboards.
![]() |
Pololu RC Switch with Small Low-Side MOSFET |
![]() |
Pololu RC Switch with Medium Low-Side MOSFET |
![]() |
Pololu RC Servo Multiplexer 4 Channel (assembled) |
Producent
Osoba odpowiedzialna
Aluminiowa obudowa do minikomputera Raspberry Pi 4 model B, kolor czarny
Brak towaru
Moduł z 7-kolorowym wyświetlaczem ACeP e-Paper o przekątnej 5.65" i rozdzielczości 600x448 px. Komunikacja przez interfejs SPI. Waveshare Pico-ePaper-5.65
Brak towaru
Moduł HAT z zegarem RTC DS3231SN oraz układem resetującym MAX705 przeznaczony dla Raspberry Pi i Jetson Nano. Na płytce umieszczono gniazdo baterii CR1220 oraz złącze USB typu C. Waveshare RTC WatchDog HAT
Brak towaru
Moduł rozszerzeń przeznaczony do współpracy z Raspberry Pi 400. Na płytce wyprowadzono dwa złącza 40-pinowe umieszczone w pozycji pionowej oraz złącze do RPI 400 pod kątem 45°. Waveshare PI400-GPIO-ADAPTER-C
Brak towaru
Moduł zasilający z zegarem RTC DS3231SN przeznaczony dla Raspberry Pi. Umożliwia zasilanie minikomputera napięciem do 28 V i tworzenie skryptów sekwencji włączania. Pimoroni WITTY_PI_3_R2
Brak towaru
Moduł 8-kanałowego ekspandera I2C opartego na układzie TCA9548A. Umożliwia komunikację z wieloma urządzeniami I2C, które mają ten sam adres. Pimoroni 8086-006
Brak towaru
Mini płytka z mikrokontrolerem RP2040 wyposażonym w dwa rdzenie ARM Cortex-M0+ 133 MHz, 264 kB RAM. Na płytce znajduje się również 8 MB pamięci QSPI flash. Układ może być programowany w C/C++, CircuitPython lub MicroPython. PIM577
Brak towaru
Moduł z czarno-białym wyświetlaczem e-Paper o przekątnej 2,13" i rozdzielczości 250x122 px. Interfejs SPI. Pimoroni PIM368
Brak towaru
Metalowa obudowa z wentylatorem dla Raspberry Pi 4 model B w kolorze czarnym
Brak towaru
Zielona, aluminiowa obudowa do komputera Raspberry Pi 4 model B. Została wyposażona w otwory montażowe standardu VESA 75
Brak towaru
Uniwersalny organizer z 36 przegrodami. Pozwala przechowywać niewielkie części i narzędzia. BOX0001
Brak towaru
Uniwersalny organizer z przegrodami. Pozwala przechowywać niewielkie części i narzędzia. BOX0002
Brak towaru
Uniwersalny organizer pozwala przechowywać niewielkie części i narzędzia. BOX0003
Brak towaru
Uniwersalny organizer z przegrodami. Pozwala przechowywać niewielkie części i narzędzia. BOX0004
Brak towaru
Uniwersalny organizer z przegrodami. Pozwala przechowywać niewielkie części i narzędzia. BOX0005
Brak towaru
Niewielki pojemnik wykonany z tworzywa szucznego, z uchwytami umożliwiającymi łączenie z innymi modułami tworząc modularny organizer. Kolor korpusu zielony z przezroczystym wieczkiem. BOX0007
Brak towaru
Pololu RC Switch with Digital Output