- Out-of-Stock

Pololu RC Switch with Digital Output
This tiny board converts hobbies radio control pulses to digital on / off RC switch and simple RC adapter applications. One output indicates the presence of a valid RC signal (10-100 Hz pulse rate, 0.5-2.5 ms pulse width), and the pulse rate is above or below the 1.6 ms threshold (with ± 0.1 ms hysteresis) .
![]() |
The Pololu RC switch with digital output can be used with standard hobby radio control systems. Example applications include converting extra RC receiver or servo controllers can not control the LEDs or RCs. MOSFETs or relays and connecting RC systems to microcontroller. Two or more of the signal is on or off. This compact unit measures a mere 0.4 "x 0.4" and weighs just 0.3 g (0.01 oz).
![]() |
The RC switch PCB has two connections, one on each side. The remote control is connected to the RC receiver or servo controller; the side with four pins has the power supply and connections. The RC signal input, the voltage can range from 0 to 7 volts, and the threshold for a logic high is approximately 1 V. The VCC pin can be connected to the RC supply, VRC, by either the RC device or the RC receiver. if the connection between the two power pins is not made, VRC can be left disconnected from the RC switch board.
The board has two steps, 20 mA each of which is capable of sourcing or sinking. The primary output, OUT, goes high (on) when the current signal is 1.6 ms. There is approximately ± 0.1 ms of hysteresis on the threshold, meaning that the pulse width will have to be approximately 1.5 ms before the output is 1.5 ms to turn off. A secondary output, GOOD, can be used to indicate the RC signal (10-100 Hz pulse rate, 0.5-2.5 ms pulse width).
An LED on the RC switch indicates the status of the RC signal (and outputs). When a valid RC signal is not detected (GOOD and OUT both low), the LED flashes with a duty cycle of approximately 50% (ie the LED is on for as long as it is off). When a valid signal is detected (GOOD high and OUT low), the LED flashes at a very low duty cycle (ie very short flashes). When a good signal is detected, the LED turns on (no flashing).
A 7-pin 0.1 "straight breakaway male header is included with the Pololu RC switch with digital output, which can be used to connect the RC switch to perfboards or breadboards.
![]() |
Pololu RC Switch with Small Low-Side MOSFET |
![]() |
Pololu RC Switch with Medium Low-Side MOSFET |
![]() |
Pololu RC Servo Multiplexer 4 Channel (assembled) |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Development kit for ST7LITE microcontrollers
No product available!
Kit with DA7280 vibration motor driver module and LRA (Linear Resonant Actuator) motor. It allows you to add vibration feedback from the device to the project. SparkFun ROB-18247
No product available!
No product available!
No product available!
No product available!
A pin expander designed for Raspberry Pi boards. It is equipped with a standard 40-pin connector for connecting a minicomputer and five sets of 2x20-pin outputs for connecting expansion modules. Pimoroni PIM322
No product available!
No product available!
No product available!
No product available!
Starter kit with STM32MP157A application microprocessor (combination of a typical processor with Cortex-A7 core and microcontroller with Cortex-M4 core). The system allows users to create applications using the STM32 MPU OpenSTLinux Distribution software for the main processor and the STM32CubeMP1 software for the coprocessor. STMicroelectronics STM32MP157A-DK1
No product available!
No product available!
No product available!
No product available!
No product available!
Development board based on GD32VF103CBT6 MCU with 32-bit RISC-V core. It is equipped with an IPS RGB LCD display with a diagonal of 0.96 inch 160x80 and a housing. Seeed Studio 102991302
No product available!
Camera module with MT9J003 sensor cooperating with ArduCam USB Shield. The maximum video resolution is 3856x2764 pixels. LS-18023 lens mount possible. ArduCam A0096
No product available!
Pololu RC Switch with Digital Output