- Out-of-Stock
CP1003 - current probe for Micsig oscilloscopes
ID: 1182399
Probe for measuring direct and alternating current with a current of up to 30 A. Works in the band up to 100 MHz, it can be connected to the oscilloscope through the UPI connector. It does not require an external power supply. Micsig CP1003
Description
Probe for measuring AC and DC current up to 30 A. Uses UPI interface. It works in the frequency range up to 100 MHz and has two measuring ranges: 6 and 30 A. The probe can work with manual or automatic regulation and is supplied with the voltage of 12 V. It can be used in industry, automotive electronics, power supplies and inverters. Dedicated to Micsig devices.
Features
- Band: 100 MHz
- Rise Time: 3,5 ns
- Ranges: 6 A or 30 A
- Sensitivity: 1V/2A (6A), 1V/10A (30A)
- Accuracy:
- 1% ± 10 mA (6 A)
- 1% ± 50 mA (30 A)
- Signal delay: ＜ 30 ns (6 A), ＜ 30 ns (30 A)
- Measurement range:
- 20 mA to 6 Apk (6 A)
- 50 mA to 30 Apk (30 A)
- Maximum Measured Current: 30 Apk, 60 Apk-pk 21.21 Arms
- Noise: ≤1.4mA RMS (20MHz band, 30A, 10X range)
- Maximum working voltage: CAI 300V
- Maximum cable diameter: 5 mm
- Overload indicator: light
- Power supply: DC 12V
1182399
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A portable tablet oscilloscope with a 10.1 inch LCD display and a touch screen. It has four channels and has good measurement parameters: 300 MHz bandwidth, 2 GSa/s sampling rate and 220 Mpts memory buffer. Micsig TO3004
zł5,699.00
24h
Available quantity: 1
Available
A portable oscilloscope for automotive applications with an 8-inch LCD display and a touch screen. It has four channels and has good measurement parameters: 100 MHz bandwidth, 1 GSa/s sampling rate and 70 Mpts memory buffer. Micsig SATO1004 Plus
zł3,756.17
24h
Available quantity: 1
Available
Probe for measuring direct and alternating current up to 30 A. Works in the band up to 100 MHz, can be connected to the oscilloscope through the BNC connector. Powered by USB. Micsig CP1003B
zł3,427.73
Delivery date unknown
No product available!
Other products in the same category (16)
Set with a 7.5" e-Paper display with passive power via NFC, NFC module and microSD card. Waveshare 7.5inch NFC-Powered HD e-Paper Eval Kit
Retired
No product available!
No product available!
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0 + cores operating at 133 MHz, 256 kB RAM. The board also has 16 MB of QSPI flash memory. The system can be programmed in C/C++ or microPython. SparkFun DEV-17717
Retired
No product available!
No product available!
No product available!
8 Mpx camera module with IMX219 sensor and wide-angle lens. To be used as a replacement on the RPI Camera Board V2. ArduCAM B0194
Retired
No product available!
Male terminal block, angled, 10-pin. Pitch 3.5mm. Height 9.2mm. KF2EDGR
Retired
No product available!
No product available!
No product available!
The P-NUCLEO-IOD01A1 is an STM32 Nucleo pack composed of the NUCLEO-L073RZ development board, the STEVAL-IOD003V1 evaluation board and the X-NUCLEO-IKS01A2 expansion board
Retired
No product available!
No product available!
No product available!
Camera module with IMX219 sensor with a resolution of 8 MP equipped with programmable focus, without IR filter. Designed for NVIDIA Jetson Nano and Raspberry Pi CM. ArduCAM B0189
Retired
No product available!
Retired
No product available!
Residual current circuit breaker ideal for protecting electrical installations in residential and commercial buildings. With high resistance to short circuits and surges, and compliance with IEC/EN 61008 standards, it ensures safe usage and long-lasting operation
Retired
No product available!
No product available!
Probe for measuring direct and alternating current with a current of up to 30 A. Works in the band up to 100 MHz, it can be connected to the oscilloscope through the UPI connector. It does not require an external power supply. Micsig CP1003