.png)
- Out-of-Stock
DP20003 - Micsig high voltage differential probe
ID: 1182398
High voltage differential probe. It is characterized by good measurement parameters: with a 100 MHz band and an operating voltage up to 5600 V. The probe has two attenuation factors: 200X and 2000X. Micsig DP20003
Description
The Micsig High Voltage Differential Probe is a probe for measuring the voltage difference between two non-earth potential test points. The device allows you to observe waveforms without grounding, variables and single measurements. It is characterized by good measurement parameters: 100 MHz band and operating voltage up to 5600 V. The probe has two attenuation factors: 200X and 2000X set by the user. It is equipped with a USB port used as a power source and a BNC connector.
The device is compatible with all oscilloscopes.
Features
- Band: 100 MHz
- Rise time: 3.5 ns
- Damping: 200X, 2000X
- Accuracy: 2%
- Maximum Differential Test Voltage (DC+AC PK): 560V (200X), 5600V (2000X)
- Maximum common mode input voltage (DC+AC PK): CAT II 1000V
- Input reference noise: ≤160mVrms (200X), ≤920mVrms (2000X)
- Common Mode Rejection Ratio: ＞80dB (DC), ＞60dB (100KHz), ＞50dB (1MHz)
- Input impedance: 50MΩ/1.25pF (differential), 25MΩ/2.5pF (one input to ground)
- Output voltage: ≤3V
- Value overflow alarm
- Input cable length: approx. 45 cm
- Output cable length: approx. 90 cm
- Power supply: 5V DC ， USB
- Power: 0.85 W
- Dimensions: 146.7 x 60 x 26.5 mm
Kit contains
- Micsig DP20003 measuring probe with input and output wires
- 2 x Crocodile clip
- 2 x clip with hook
- USB cable
1182398
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
You might also like
Micsig differential probe from the DP series designed for high-voltage and differential signal measurements. Offers 100 MHz bandwidth and supports voltage measurements up to 700 V. Features a standard BNC connector and USB Type-C power supply. The current product revision includes a new enclosure with three function buttons. Micsig DP700
zł1,326.46
24h
Available quantity: 1
Available
Other products in the same category (16)
Assembled falling meteorite. AVT3186 C
Retired
No product available!
Printed circuit board and programmed thermostat system with LED display. AVT3220 A +
Retired
No product available!
AVT kit for self-assembly of a thermostat with LED display. AVT3220 B
Retired
No product available!
Assembled thermostat with LED display. AVT3220 C
Retired
No product available!
A circuit board for the (half) home automation system - a four-channel ON / OFF module. AVT3212 A
Retired
No product available!
AVT kit for self-assembly of the (half) home automation system - four-channel ON / OFF module. AVT3212 B
Retired
No product available!
Assembled system (half) of home automation - four-channel ON / OFF module. AVT3212 C
Retired
No product available!
The PCF8574 IO expansion board is an 8-bit I / O expander controlled by the I2C interface. Up to 8 PCF8574 IO expansion cards can be connected to the I2C bus, providing up to 64 I / O ports. Waveshare 3708
Retired
No product available!
MYIR MYS-7Z0007S-C - KIT is a set of elements with a single board computer based on the Xilinx XC7Z007S-1CLG400C (Zynq-7007S) system. This system consists of a single-core processor based on Cortex-A9 core, which can operate at a maximum frequency of 667 MHz and Artix-7 FPGA. The computer is equipped with 512 MB of DDR3 SDRAM, 4 GB of eMMC memory and 16 MB of QSPI Flash memory
Retired
No product available!
MYIR MYS-7Z0007S-C is a single board module based on the Xilinx XC7Z007S-1CLG400C chip (Zynq-7007S). This system consists of a single-core processor based on Cortex-A9 core, which can operate at a maximum frequency of 667 MHz and Artix-7 FPGA. The computer is equipped with 512 MB of DDR3 SDRAM, 4 GB of eMMC memory and 16 MB of QSPI Flash memory
Retired
No product available!
MYIR MYIR MYS-7Z010-LC is a set of elements with a single board computer based on the Xilinx XC7Z010-1CLG400C (Zynq-7010) system. This system consists of a dual-core processor based on Cortex-A9 core, which can operate at a maximum frequency of 667 MHz. The computer is equipped with 512 MB of DDR3 SDRAM, 4 GB of eMMC memory and 16 MB of QSPI Flash memory
Retired
No product available!
MYIR Z-turn Lite MYS-7Z010-LCS is a single board module based on the Xilinx XC7Z010-1CLG400C (Zynq-7010) chipset. This system consists of a dual-core processor based on Cortex-A9 core, which can operate at a maximum frequency of 667 MHz. The computer is equipped with 512 MB of DDR3 SDRAM, 4 GB of eMMC memory and 16 MB of QSPI Flash memory
Retired
No product available!
Z-turn IO Cape extension board is an extension board for Z-turn series tiles based on Xilinx Zynq
Retired
No product available!
No product available!
OLED display 128x64 pixels, 0.96 ", 3V power supply, SSD1306 controller, communication via I2C and SPI interfaces, PARALLEL WHITE display color, working temperature from -40 to +70, ext. CAP
Retired
No product available!
ODROID-HC2 is a mini PC with Samsung Exynos5422 Cortex-A15 2Ghz and Cortex-A7 Octa core CPUs
Retired
No product available!
High voltage differential probe. It is characterized by good measurement parameters: with a 100 MHz band and an operating voltage up to 5600 V. The probe has two attenuation factors: 200X and 2000X. Micsig DP20003