AltIMU-10 v5 Gyro, Accelerometer, Compass, and Altimeter (LSM6DS33, LIS3MDL, and LPS25H Carrier)
ID: 561044
zł154.57
Tax included
zł125.67 tax excl.
Inertial measurement unit (IMU) and altimeter that features the same LSM6DS33 gyro and accelerometer and LIS3MDL magnetometer as the MinIMU-9 v5, and adds an LPS25H digital barometer. Pololu 2739
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
The Pololu AltIMU-10 v5 is a compact (1.0″ × 0.5″) board that combines ST’s LSM6DS33 3-axis gyroscope and 3-axis accelerometer, LIS3MDL 3-axis magnetometer, and LPS25H digital barometer to form an inertial measurement unit (IMU) and altimeter; we therefore recommend careful reading of the LSM6DS33 datasheet (1MB pdf), LIS3MDL datasheet (2MB pdf), and LPS25H datasheet (1MB pdf) before using this product. These sensors are great ICs, but their small packages make them difficult for the typical student or hobbyist to use. They also operate at voltages below 3.6 V, which can make interfacing difficult for microcontrollers operating at 5 V. The AltIMU-10 v5 addresses these issues by incorporating additional electronics, including a voltage regulator and a level-shifting circuit, while keeping the overall size as compact as possible. The board ships fully populated with its SMD components, including the LSM6DS33, LIS3MDL, and LPS25H, as shown in the product picture.
The AltIMU-10 v5 is also pin-compatible with the MinIMU-9 v5 and offers the same functionality augmented by a digital barometer that can be used to obtain pressure and altitude measurements. It includes a second mounting hole and is only 0.2″ longer than the MinIMU-9 v5. Any code written for the MinIMU-9 v5 should also work with the AltIMU-10 v5.
Features
- Dimensions: 1.0″ × 0.5″ × 0.1″ (25 mm × 13 mm × 3 mm)
- Weight without header pins: 0.8 g (0.03 oz)
- Operating voltage: 2.5 V to 5.5 V
- Supply current: 5 mA
- Output format (I²C):
- Gyro: one 16-bit reading per axis
- Accelerometer: one 16-bit reading per axis
- Magnetometer: one 16-bit reading per axis
- Barometer: 24-bit pressure reading (4096 LSb/mbar)
- Sensitivity range:
- Gyro: ±125, ±245, ±500, ±1000, or ±2000°/s
- Accelerometer: ±2, ±4, ±8, or ±16 g
- Magnetometer: ±4, ±8, ±12, or ±16 gauss
- Barometer: 260 mbar to 1260 mbar (26 kPa to 126 kPa)
561044
Data sheet
- Interface
- I2C
- Type of sensor
- LSM6DS3
- Module type
- 10DoF
- Power supply voltage
- 2,5 - 5,5 V
- Sensor type
- Akcelerometr, żyroskop, magnetometr i barometr
You might also like
MEMS accelerometer, magnetometer and gyroscope on a single die with a high speed ARM Cortex-M0 based processor
zł239.00
Delivery date unknown
No product available!
Other products in the same category (16)
Module with 9-axis IMU BMX160 sensor (accelerometer, gyroscope and magnetomet) and BMP388 pressure/temperature sensor. Communication via the I2C interface. DFRobot SEN0252
zł99.10
4 weeks
No product available!
Module with 9-axis IMU dedicated to Feather plates. It connects the ISM330DHCX (accelerometer and gyroscope) and LIS3MDL (magnetometer) systems. Communication via the I2C interface. Adafruit 4569
zł173.93
24h
Available quantity: 1
Available
Module with 9-axis IMU. It combines the ISM330DHCX (accelerometer and gyroscope) and MMC5983MA (magnetometer) systems. Communication via the I2C interface. SparkFun SEN-19895
zł223.97
24h
Available quantity: 2
Available
Module with 9-axis IMU ICM-20948 sensor. The system is an integrated 3-axis accelerometer, gyroscope and magnetometer and a digital motion processor DMP (Digital Motion Processor). Communication via I2C. Pimoroni PIM448
zł92.90
24h
Available quantity: 3
Available
Module with 6-axis IMU sensor that allows you to measure acceleration and rotational speed in the range up to ±16g and ±2000dps. Equipped with a STEMMA QT connector, it communicates via I2C or SPI. Adafruit 4503
zł55.02
4 weeks
No product available!
The module with the ADIS16470 chip, which combines a 3-axis accelerometer and a gyroscope. The board is equipped with a Grove connector and communicates via the I2C or SPI interface. Seeed Studio 101020672
zł1,941.11
6 weeks
No product available!
MEMS accelerometer, magnetometer and gyroscope on a single die with a high speed ARM Cortex-M0 based processor
zł239.00
4 weeks
No product available!
Module with a 9-axis IMU sensor, which combines an accelerometer and a gyroscope (ICM20600 system) and a magnetometer (AK09918 system). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020585
zł62.87
24h
Available quantity: 1
Available
Small 10 DoF IMU module with 3-axis gyroscope and accelerometer (LSM6DSO), 3-axis magnetometer (LIS3MDL) and barometer (LPS22DF). It is equipped with an I2C interface, a voltage stabilizer and a voltage level converter. Pololu 2863
zł131.00
24h
Available quantity: 1
Available
The GY-87 module is composed of a module with MPU6050, QMC5883L and BMP180 sensors, allowing the measurement of traffic in nine axes and the measurement of atmospheric pressure. The module has a built-in 3.3 V voltage stabilizer
zł31.44
6 weeks
No product available!
Module with LSM6DS3 sensor that combines a 3-axis accelerometer and a 3-axis gyroscope. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 105020012
zł67.69
24h
Available quantity: 1
Available
KAmodLSM6DS3 is a module that allows measurement of acceleration and angular velocity values. It has a built-in voltage stabilizer and level translators on SDA / SCL lines, thanks to which it can be used in 2.5-5.5V voltage systems
zł27.47
24h
Available quantity: 189
Available
A module with an acceleration and rotational speed sensor based on the ICG-20660L system. It communicates via the I2C or SPI interface. DFRobot SEN0443
zł114.13
24h
Available quantity: 3
Available
Module with 9-axis IMU ICM-20948 sensor. The chip is an integrated 3-axis accelerometer, gyroscope and magnetometer and a digital motion processor DMP (Digital Motion Processor). Communication via I2C or SPI. SparkFun SEN-15335
zł103.78
24h
Available quantity: 6
Available
GY-801 is a 9DOF IMU module with L3G4200D, ADXL345, MMC5883MA and BMP180 systems. It allows you to measure the movement of the object and atmospheric pressure.
zł152.75
24h
Available quantity: 2
Available
Module with acceleration and rotational speed sensor based on the MPU6050 system. It communicates via the I2C or UART interface
zł65.90
24h
Available quantity: 5
Available
Inertial measurement unit (IMU) and altimeter that features the same LSM6DS33 gyro and accelerometer and LIS3MDL magnetometer as the MinIMU-9 v5, and adds an LPS25H digital barometer. Pololu 2739